0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
When using an adjective to describe one thing use the what degree?
When using an adjective to describe one thing, use the positive degree. (Wikipedia)
When using an adjective to describe one thing use the degree?
dsdfsadf
How do you construct 65 Degree angle?
By using a protractor and a straight edge
How do you find degree of hypotenuse on a right angle triangle?
By using trigonometry
How do you make a 110 degree angle using a ruler and a compass?
use trisection method
When bending a 12 inch offset using 30 degree bends what would the distance between the two bends?
Use these numbers when bending offsets: 10 degree bends, multiply the depth of the offset by 6 this will give you the distance between bends. For 20 degree multiply by 2.6, for 30 degree multiply by 2, for 45 degree multiply by 1.4, for 60 degree multiply by 1.2. I use 30 degree bends for all of my offsets, just because its easier to do the math. So your answer would be 24 inches between bends. I have come to the conclusion anybody can bend conduit, its the measuring and marking that requires skill.
When bending a 12 inch offset using 30 degree BENDS what would be the distance between the two bends?
Use these numbers when bending offsets: 10 degree bends, multiply the depth of the offset by 6 this will give you the distance between bends. For 20 degree multiply by 2.6, for 30 degree multiply by 2, for 45 degree multiply by 1.4, for 60 degree multiply by 1.2. I use 30 degree bends for all of my offsets, just because its easier to do the math. So your answer would be 24 inches between bends. I have come to the conclusion anybody can bend conduit, its the measuring and marking that requires skill.
When bending a 12 inch offset using a 30 degree bend what would the distance between the two bends?
Use these numbers when bending offsets: 10 degree bends, multiply the depth of the offset by 6 this will give you the distance between bends. For 20 degree multiply by 2.6, for 30 degree multiply by 2, for 45 degree multiply by 1.4, for 60 degree multiply by 1.2. I use 30 degree bends for all of my offsets, just because its easier to do the math. So your answer would be 24 inches between bends. I have come to the conclusion anybody can bend conduit, its the measuring and marking that requires skill.
What are the implications of using offsets by an operating system?
your mom
Using your finger how long is an inch?
From the tip of your pinky to where it bends in the middle
How do you set work offset in makino a51 machine?
There are two ways to load offsets into any Makino Pro 5 machine. The first is by using menus. In the bottom left corner of the touch screen there is a arrow press that. The extended manual will pop up with a dozen or so buttons. Each will bring up a new screen. Press the Work Offsets button. Listed there are all of your work offsets with fields that can be filled out. TL:DR - Little arrow in bottom left>Work Offsets The other way to create work offsets is to load them in through programming. An couple example lines of this is G90 G10 L20 P01 X-18.378 Y-22.8265 Z-23.5123 G90 G10 L20 P02 X-18.456 Y-17.8265 Z-23.5142 "G90 G10 L20" is the code to load the offsets and it will always remain the same. For work offsets G54.1 P__. I do not remember the code for G54-G59 offsets off of the top of my head. P01 through P48 or P300(extended offsets) will select the work offset you want. X____Y____Z____B____ will be your offsets to be loaded in.
How do you get rid of headaches after trying to do back bends?
try using advil or something or wear it out
Which term indicates any curved and transparent object refracts or bends light?
if you are using A+ it is lens
Terms indicates any curved and transparent object that refracts or bends light?
if you are using A+ it is lens
What does a rolling offset look like?
rolling offsets are used in the piping and sheet metal (duct work) trades, a rolling offset changes the elevation and locaton of the piping or duct usually by using two fittings to offset around obstacles. rolling offsets are used mostly when you are limited to the size of the fittings in order to change your elevation and location rolling offsets are used in the piping and sheet metal (duct work) trades, a rolling offset changes the elevation and locaton of the piping or duct usually by using two fittings to offset around obstacles. rolling offsets are used mostly when you are limited to the size of the fittings in order to change your elevation and location
What is offset address?
An offset address is a relative address rather than an absolute address. You use offsets to refer to memory relative to an absolute address. For instance, array indices are implemented using offsets from the start address of the array, such that element 0 is at offset 0 and element 5 is at offset 5.
Is it bachelor's degree or bachelor degree?
It depends on the context of which you are using the word. "I have a bachelor's degree," or "I have a bachelor of arts degree."
