0
Kanika Exports are manufactures & exporters of various types of products like- Threaded Rods/ Bars, Coil Rods/ Tie Rods , Threaded Studs, Hex Nuts, Hex Bolts, Plain Washers, Spring Washers, Spring Channel Nut,Strut Channel ,Channel Accessories ,Channel Brackets, Channel Fitting Accessories, Mild Steel Threaded Rods , Zinc Plated Threaded Rods, Steel Threaded Rods, Medium Carbon Steel Threaded Rods, Double Ended Threaded Rods, Fully Threaded Studs, Rolled threaded bars,MS thread rods and bars, UNF Threaded Rods, UNEF Threaded Rods, UNC Threaded Rods, Unified Threaded Rod
What else can I help you with?
What is the mass of 2 hex nuts?
That depends entirely on the size and composition of the hex nuts.
What size lug nuts come on a 1998 Dodge Intrepid?
12x1.5 with a 19mm hex head. 12x1.5 with a 19mm hex head.
How do you tighten a bathroom sink faucet?
Hand tight. just use the plastic nuts that came with it. With a basin wrench to secure the 1/2" hex nuts
What are the different types of screw nuts and how are they used in various applications?
There are several types of screw nuts, including hex nuts, wing nuts, and lock nuts. These nuts are used in various applications to secure bolts or screws in place. Hex nuts are the most common type and are tightened with a wrench. Wing nuts are easy to tighten by hand and are often used in applications where frequent adjustments are needed. Lock nuts have a built-in mechanism to prevent loosening due to vibrations or other factors. Each type of nut is chosen based on the specific requirements of the application to ensure a secure and reliable connection.
How do you change a headlight on an 2003 astro van?
step1. open the hood and remove the hex nut holding the outer light portion in place. step2. remove the hex nuts above the light assembly step3. remove the hex nut to the side of the lights to allow them to lean forward step4. allow light assembly to move forward and twist the light to remove from the assembly step5. replace bulb step 6. replace light assembly and all hex nuts
Remove valve cover on 1998 rav 4?
The short answer is: * remove vacuum lines * remove plug wires * detach throttle cables from linkage * remove spark plugs * remove 4 large hex nuts * remove washer/seals found beneatch hex nuts * remove valve cover
What size are the lug nuts on a 1997 Plymouth Voyager?
The size of lug nuts on a 1997 Plymouth Voyager is a Hex Size of 3/4 inches. The length of each lug nut would be 1.45 inches.
What metric size are the lug nuts on 1996 Volvo 850?
The lug nuts for the 1996 Volvo 850 are 65.8 mm in length, and the hex size is 19 mm. The thread size is M12 x 1.75. Some brands of lug nuts for this car are McGard and Dorman.
How do you remove the third row seat in a Rendezvous?
All you need is a 1/2 socket, preferably deep socket, and a 1/4 hex wrench, preferably a torx wrench. Inside the rear floor storage compartment, remove the 2 silver hex head nuts. This will then allow you to remove the storage compartment. Then use the 1/4 hex wrench (actually this is a torx screw, but the hex wrench works) to remove the seat belt mounting to the floor. Fold the seat down, if not already done so. Then go under the front of the third row seats and remove the two hex nuts. With all four nuts and the torx bolt removed, you can lift out the seat. **Minor Edit** I find it easier to leave the seat in the up position to remove the front seat boltsthen fold it down. i dont think you can even get to them when the seat is folded flat.
What nicknames does Brandon Hex go by?
Brandon Hex goes by Brandon Hex.
How do you remove axle of a Yamaha warrior 350?
Remove the left tire, remove the two hex nuts near rear sprockets, remove the left hub, take off the sprocket along with the two hex nuts, put the left hub back onto the axle and take a socket and tap the hub. The axle should come out on the right...if it don't email me and tell me how to get it off cause that's where I am stuck right now.
Why are hexagonal headed bolts and nuts usually preferred to square headed bolts and nuts?
Having 6 points of contact rather than just 4 (for square bolts and nuts) reduces the tendency to damage the nuts by shearing the edges. Of course, square bolts have an advantage if using an alternative tool (pliers, lock-grips) to hold or turn the bolt, because there is a wider surface to grip than with hex bolts.
