0
This is one that should be left for a qualified person. As the job can effect life and limb a permit should be taken out and the job inspected. Failure to do this can leave you responsible if someone should get hurt due to faulty wiring or practices. Sorry, get an electrician and insist he takes out a permit and an inspection is done.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What gauge wire is required to hook up an electric kitchen stove?
Normally a new kitchen stove will require a 50 amp breaker wired with AWG # 6/3 with ground wire.
How do you hook up a three phase welder?
Easy as one,two and three. There are four primary wires coming from you service panel.(provided you have three phase service) you can check by looking at the weather head on the roof. if it has three wires you have single phase but if it has four then you have three phase. the hot wires will be black,red and brown. the neutral will be white or green. the welder should have a manual that will give you the lead phase wire(most likely black to black) the other two hot wires can hook to any other hot wire. The neutral goes to the white or green and posts to the panel. If the welder has a switching power supply then you must have a three phase converter.
How do you hook up a live wire into two switches?
First turn off the power. You can do it a couple of ways. Take your black hot wire and connect two black pigtail wires of the correct gauge to the wire via a wirenut. Then connect each of the two pigtails to each switch. Another way if the supply wire is long enough you can strip about 1/2 inch off about 4 inches from the end. Make a "U-shaped" bend in the stripped area and put that around one switch and strip the end and connect to the other switch.
Can a three way switch be changed to a single pole switch with a plate over one of the switch locations?
Yes, If you only hook up two wire it will work as a single pole
Is it possible to run power from a three way switch to install an outlet?
Yes you just have to "steal" power from the switch. Do this by running a pigtail wire from the hot of the switch to the hot wire of the plug. Make sure you do this before the switch or you will end up with your outlet being switched as well.
If you are trying to hook up a tach to your '90 Bonneville which wire should you hook it up to to get an rpm reading?
to hook up the tach use the hot lead on the disributor and to any good ground wire and if there is a light hook it to the wire on you light switch
Where do you hook up the remote wire for a amp in a 2008 Impala?
Get a multimeter and find any hot wire going to the stereo when key is on.
As soon as you hook up hot wire to cigarette lighter the fuse blows on your 84 Chevy pickup why?
Load is too large for the circuit, or there is a short in the wire you are hooking up.
How do you hook up the molecules on the hot tub on my sims agents?
It's nearly impossible to explain, but if you go onto you tube I'm certain you will find a tutorial on how to do it.
Where hook up interior lights in 1969 Chevrolet?
I believe that it is a grounding switch. If that is the case it would only have one wire going to the switch. You could run this wire to any fused constant hot. The wire would run from the hot, to the light, to the switch.
What is the average price of a hot tub installation?
The average cost of a hot tub installation is about $1000 +. You have to hire a plumber and an electrician to set up a hot tub as well as a carpentar if you would like to build an area around the hot tub, such as a deck.
Do you pay monthly for internet or can you hook up to Hot Spot for free?
you can hook up to Hot Spots for free
How long do hot tub covers last?
Hot tub covers can have long lives if they are cared for properly. Hot tub covers are mostly affected by dirt and sunlight so keep it clean and perhaps put a tarp over it if the hot tub is in direct sunlight.
How do you hook up your cooling fan to your battery?
A person can hook up a cooling fan to a battery by connecting the hot or positive lead to the positive side of the battery. The negative lead wire is then connected to the negative side of the battery.
Do you hook up the ground wire first to an amp?
No. Hook up the power wire first, then the ground wire. The ground wire is what acutually draws the power to the unit. As you will notice the power wont turn on if just the power wire is plugged in..
How do you hook up pro tach rpm gauge on a 1982 ford F-150 pickup?
Hook up the red wire to the fuse box or another wire that gives power when the key is on. Hook up the white wire to a wire coming out of the headlight switch. This will make is so that when you turn your headlights on, the light will come on on the tach. If you don't mind the light on the tach being on all the time then just hook it to another power wire. Hook the black wire to a ground like a screw or a bolt. The green wire is the signal wire. Run it through your fire wall. Hook it up to the negative side of the coil. There will be a negative sign on the coil denoting the correct side.
What battery wire to you hook up first in a car battery?
Hook positive up first, negative last.
