0
How can you connect electric to food disposal having the wire under the sink without switch?
Wiki User
∙ 15y ago
You must have a switch to turn the disposal on and off. If you are asking how to connect because you do not have a switch. Install the switch under the sink just above the door opening. You can buy disposals that turn on and off when you place the lid over the hole. InSinkerator makes one.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What are the parts and components of a cordless electric drill?
There are only a few parts and components that separate a cordless electric drill from a corded electric drill. Having a battery instead of a cord is the biggest difference.ÊÊ
How do current clamp on amp meters work?
clamp is an electrical device having two jaws which open to allow clamping around an electrical conductor. This allows properties of the electric current in the conductor to be measured, without having to make physical contact with it, or to disconnect it for insertion through the probe.
Do you have to Connect both fixture and house ground wires?
If you're asking whether you have to connect the fixture ground to the house ground, you do. The idea is to connect any exposed portion of a metal fixture to ground, keeping anything you would be able to touch from having a hazardous potential on it. The way to do this is to connect the fixture ground (which is connected to the metal chassis) to the building ground (which comes from your electrical panel).
Convert oil furnace to electric?
"Converting" an oil furnace to electric will not be economically practical. You'd be far better off getting a "ground source heat pump" and having someone install it for you. They're much more efficient than the older style electric heat that uses resistor heating elements.
What is a source in an electrical circuit?
The source in electric cuircuit is having sex with a woman.
How do you install pro tools LE without having to connect any hardware?
You can't. You need to connect the hardware to install it.
Can you hook your Xbox 360 to Xbox live without having a computer?
to connect to xbox live you need a router or a modem
What is the point of having an electric motor?
It makes work easier than doing everything by hand without the motor.
Where do you connect the leads of your tester to test a electric hot water heater thermostat without having the power connected or the tank full of water?
what you actually want to do is use a continuity tester, the element actully gets because it creates a controlled short, kind of like if you touch a wire to both posts on a battery any how there are two screws on each element that is where you connect the tester.
How can one join the community without going through Facebook?
There used to be an option where you could join Wiki Answers without having to connect Facebook. Unfortunately, they have removed this feature.
What is an electric pallet jack?
An electric pallet jack or electric pallet truck is powered by an electric motor. Allowing the operator to move pallets without having the manually pump/push to lift and/or move pallets. They come in both walk behind and ride on configurations.
How do you connect two computers to the internet without having the IP addresses conflict with each other?
By using a router with DHCP turned on in the router
Which type of standard interface allows users to connect and disconnect peripheral devices while the computer is running without having to restart?
USB
Is it possible to install an external electric fuel pump on a 1999 firebird without having to remove the internal one from the gas tank?
no!
When do you replace your epilator?
Many times, it is possible to use an epilator for 10 to 15 years without having to replace it. This will help you save money from having to buy disposable and electric razors.
How do you make your own flashlight without having to buy one?
Connect a light bulb to a battery, and put the whole thing in a tube so you can hold it.
How do you extend the electric outlet at the basement?
Parallel connect the new receptacle to a receptacle in the existing circuit. Black (hot) existing to black (new), white existing to white (new), ground existing to ground (new). Make the ground wire coming into the new receptacle box longer so that it can be looped around the ground screw located in the receptacle box first and then connect to the receptacle without having a break in the wire.
