There are multiple ways to wire a switch. If power is fed into the switch box, a second light would be wired one way, if power is fed into the light box, the second light would be wired a different way.
This seems like it would be a task better given to a qualified electrician or local handyman.
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
Run the power line to a light box in each room, then drop a switch leg from each light box. The power line should daisy-chain to each box, with a "tap" off for the lights of each room. If you do not have experience with lighting or switch logic, it would be much more safe for you to contract with a qualified electrician.
You would need to purchase a duplex switch. As for the pilot light look for a duplex switch that has a neon pilot light that is incorporated into the handle of the switch. When the switch is turned on the switch's handle will illuminate.
The switch sounds like it might be arcing. Switches are inexpensive, change it out with a new one. With the power off and the old switch removed check the connections in the switch junction box for loose splices or burnt wire nut connectors. If everything is fine there check the light junction box for loose connections.
The pre wire for a ceiling fan light should be made with a three wire cable. This cable will have a red, black, and white wire as main conductors. This cable will also have a bare ground wire. This wire should be strung between a two gang switch box to the fixture junction box. This pre wire allows the supply to be either fed to the two gang box. From the two gang switch junction box, one side will be used for the light in the fixture and the other side of the switch junction box, itwill be used for the fan portionin the fixture.
Yes this is done all the time in house wiring. The power source is brought to a light switch's junction box. The source for the light is taken through the switch to turn the light off and on. The same source feeder is then taken to receptacle junction boxes to power devices that have to be plugged in.
Standard is 48" to the top of the switch box.
You will want to leave about 8" of wire sticking out of the box. After connecting the light just push the extra back into the ceiling box.
Only if the existing switch box has an unswitched hot and neutral in it.
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
Some brand fans have a remote control kit that installs in the fan housing. Also if you have access you can run a separate switched voltage to the fan. In this case you would have to put a second switch in the same box that controls fan, unless it is a switch with speed control that came with fan. In this case you would have to install a new box (Old Work Switch Box from Home Depot or Lowes for example) and run voltage to the box, install a switch and run wire to fan and connect to light. One other possibility is to check the ceiling box and see if there is a spare red wire. If so you could use this to switch power to the light separately from the fan. Again it depends on the switch configuration and supply voltage feed.
Answer for USA, Canada and countries running a 60 Hz supply service.Yes you can, but the light will only come on when the fan is operating. If there is a three wire going up to the fan from the light switch box then it was pre-wired so that a separate run for a light to be operated independent from the fan. The cable will be a red, black and white wire. The black will connect to the fan, the red to the light in the fan and the white to both the neutrals of the fan and light which is up in the fan housing.If the switch box is only a single gang box there is a duplex switch that can be installed in the box. The cover for this duplex switch is the same cover as a duplex receptacle cover.
in glove box
gear box
If you have one wire into your switch box for your light. this is called a switch leg, the dimmer should be wired across the black and white wire wires.
There are lots of diagrams on web under 3-way switch. However, the general principle is as follows. There are three terminals on each switch. One is the common and the other two can be used interchangeably. You connect the others together one for one between two switches. Then one switch common goes to supply voltage (Whichever box has the supply) and the other switch common goes to the load. Connect the supply white wire to the white wire in the light. If supply and load are in different boxes you will have to use one of the wires to connect together the neutrals between boxes. If they are both in same box you have to use extra wire to extend the common to the box where the supply and load do not exist.
Switch or relay? The switch is in the dash to the left of the steering wheel. The relay is in the fuse box out in the engine compartment, check the lid of the fuse box to determine the relay location within the box.