0
The length is calculated by a number of factors. The most basic example is as follows. Say a bar is required to be u shaped. It is to be placed in a 12" wide block. The bar bend would be the length of the block (12") minus a clearance on each side of the block. This clearance allows protection to the bar from weather and moisture. Typically the clear dimension is 2" or 3", depending on location in structure and engineer's specifications. That said, assuming a 2" clearance, the above example would be 12" - 2" - 2" = 8". That dimension is the out to out dimension of the rebar for that side of the bend.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you calculate length of the bend pipe?
the bend length is triple time divided and four time added with your lucky number whatever it is and subtract with your mobile number AND then multiply with zero and finally we get the total length of bend
How do you calculate rebar?
80% 3,425 lb
What is the formula for rebar?
You have to find a chart that will indicate the weight per unit of measure for the appropriate rebar size. Than take that and multiply it by the the length of the rebar. For example, a #4 rebar weighs 0.668 lbs/ft. If you have 5 @ 20-00 pieces that is 0.668 X 20 X 5 = 67 lbs. Charts are available throughout the web or at CRSI.org.
How do you estimate rebar?
To estimate the amount of rebar, a set of structural drawings are required. Once you have this information you will review the plans locating the sizes, spacings, configurations and locations of the rebar required. Each of these are reviewed in conjunction with the overall scope of the project. Using a means of tabulation, either via computer or paper, you roughly calculate and list each item. Then the tabulation can be utilized to calculate the weight and totals of the material to be used.
How do you calculate kg of steel reinforcement in one cubic meter concrete?
it would depend entirely on the rebar design.....
What is the weith 168x27-7 rebar?
You need the size of the rebar involved to calculate the weight. Charts can be found at CRSI.org or Rebarapps.com. Than take that and multiply it by the the length of the rebar. For example, a #4 rebar weighs 0.668 lbs/ft. If you have 5 @ 20-00 pieces that is 0.668 X 20 X 5 = 67 lbs. You need to know the size of the bar to calculate.
How do you calculate length of the bend pipe?
the bend length is triple time divided and four time added with your lucky number whatever it is and subtract with your mobile number AND then multiply with zero and finally we get the total length of bend
How do you calculate rebar?
80% 3,425 lb
What is the formula to calculate rebar weight?
You have to find a chart that will indicate the weight per unit of measure for the appropriate rebar size. Than take that and multiply it by the the length of the rebar. For example, a #4 rebar weighs 0.668 lbs/ft. If you have 5 @ 20-00 pieces that is 0.668 X 20 X 5 = 67 lbs. Charts are available throughout the web or at CRSI.org.
What is the difference between lap splice length and development length for rebars?
The difference between the two is in the application. A development length is the amount of rebar length that is needed to be embedded or projected into concrete to create a desired bond strength between the two materials. The lap splice length is the length two rebar pieces must overlap and be tied together to create a bond as if there was no break and the run is "continuous". So simply put, development is rebar to concrete, splice is rebar to rebar. The lengths of both splice and development do vary. They are dependent upon different factors. These include but are not limited to concrete strength, rebar size, rebar coating and concrete cover or clearance. So when you see a chart on one project, it can differ from another for these reasons.
How do you bend the rebar?
Either just grab it and bend it around something or use a length of pipe, stand on one side and slide the pipe over the other end and bend it. You can stick it in something solid and bend it with the pipe then.
How do you calculate developed length of sheet metal forming?
ON the cad offset the bend radius from the internal radius of the sheet metal part by 40% of the total sheet thickness,and measure the chord length of the radius. that will be the developed length.
What is the formula for rebar?
You have to find a chart that will indicate the weight per unit of measure for the appropriate rebar size. Than take that and multiply it by the the length of the rebar. For example, a #4 rebar weighs 0.668 lbs/ft. If you have 5 @ 20-00 pieces that is 0.668 X 20 X 5 = 67 lbs. Charts are available throughout the web or at CRSI.org.
How do you estimate rebar?
To estimate the amount of rebar, a set of structural drawings are required. Once you have this information you will review the plans locating the sizes, spacings, configurations and locations of the rebar required. Each of these are reviewed in conjunction with the overall scope of the project. Using a means of tabulation, either via computer or paper, you roughly calculate and list each item. Then the tabulation can be utilized to calculate the weight and totals of the material to be used.
What is the formula for computing the surface area of a pipe elbow?
Calculate as you would the surface of a cylinder who's height is the length of the central line of the pipe bend.(2*π*r*h)where:r is the (external) radius of the pipeπ is the constant 3.14159... andh is the length of the cylinder or the center-line of the pipe bend
How much 16MM rebar in 1 ton?
16mm weighs 1.552 kg/m 1 metric tonne 1000 kg So about 644m length
What is rebar detailing?
Rebar Detailing is a procedure of making shop drawings for the steel reinforcement for the development procedure. The Rebar Detailing procedure incorporates the position, bending shapes, amount, description, laps of the reinforcing steel and measurements. The Rebar Detailing Drawings are made to incorporate the separating, area, rebar size and lap of steel. The Rebar Detailing Services includes: Rebar Detailing Services, Rebar Shop Drawings Services, Rebar fabrication Services, Rebar Framing Plan Design, Rebar Structure Foundation, Rebar Pit Design, Rebar Framing Plan, Rebar Beam Design, Rebar Structure Steel Detailing, Structure Foundation Rebar Detailing.
