My switch failed. I got the switch out ok (just put your hand up and pull the wire whilst pushing the switch up through the hole. The switch was badly burned, but I filed the contacts and then cable-tied the switch to the steel rod that secures the bottom of the fascia, so that as the pedal came up it opened the switch! You do need to remove the air link pipe to the o/s vent though as the switch protrudes into this space.
Hi Had same problem with my 306 and found easiest way was to unbolt the four bolts holding the steering column up and lowering it down as far as it will allow, then you can gain access to switch through small cut out on clutch side of brake pedal(very tight and awkward) but i did manage to replace mine......Hope this helps.
Brake switch on the 306 is mounted high up on the brake pedal. The access to it is from behind the fascia, in other words one big job stripping out all the instruments, glove box and everything else. may be able to access it by removal of the instrument (rev counter and speedo) panel. I am about to try this method if i can remove the top instrument screws, 1.5mm hex wrench but heads have become rounded. Would as yourself be glad to hear of a quicker fix.
I did my 2000 306 HDi today. Remove the plastic fuse box cover. Remove the convoluted air pipe. Remove the 4 nuts that hold the steering column and lower it as far as it will go. Sit in the seat (ie you dont have to be laying in the footwell upside down) put your hand in above the column and up through the hole, the switch is to the right, (RH drive car) pull the wire and the switch will come out of the hole in the bracket. Afrter plugging a new switch into the loom, push the switch throught the hole, turn on the ignition, keep pushing the switch in (it clicks every time it goes in further) until the brake lights go off. Press one more click. Bolt in column, replace air pipe and fuse box cover. Hard the first time, 20 minutes after you have done it!
Hi. Did my 306 1.9 TD XR 1998 yesterday. Unbolting and lowering the steering column did the job. Very easy, however be carefull when refitting the steering column as it allows some adjustmest from side to side. Watch for the marks made by nuts.
In order to change the brake light switch in a Peugeot 307, you must dismantle and access the main light board on the dash and find the connecting switch, thusly flipping it back to the on position.
already changed brake switch but cant shift form P
the brake light fuse on a peugeot partner is F1O!! STOP SWITCH FUSE!!
The brake light switch is located beneath the dashboard. The switch is on the left-hand side of the drivers side.
The Chevrolet Colorado brake light switch is quite simple to change. The brake light switch simply plugs in and out.
The brake light switch must be broken or out of adjustment.
Were and how do you change a brake light switch on a Daewoo Leganza 2001
how do you change the brake light bulb on a Peugeot 3008 Halfords cant figure out how to get access
probably the brake light switch on the pedal if none are working at all
how to change brake light switch in a 2007 chevy colorado
Changing the brake light relay switch on your 1999 Chevy Cavalier is quite easy. The brake light switch simply plugs in and out.
It is quite simple to change the brake light switch on your 1998 Chevy S 10 pickup truck. The brake light switch simply plugs in and out.
To change the brake light switch on a 1999 Deville, remove the screws on the switch. It is located right on top of the brake pedal under the dash. It works as an open circuit.
You will need to change the brake light switch. The brake light switch can be found below the dashboard on the drivers side.
it says in manual that its behind the steering column only if its not a automatic
where is brake light switch
On most vehicles pressing the brake pedal activates a brake light switch which is usually located near the brake pedal. It will be this switch that is faulty. Replacing it is probably the best option.
On the turnsignal/light switch lever, on the same turn ring switch as rear fog light. If not you got change it to one with it.
Have you tried brake light switch located on brake pedal or in that area?
The 1993 Jeep grand Cherokee brake light switch simply plugs in and out. The brake light switch is located beneath the dashboard on the drivers side of the engine compartment.
change the wheel cylinders or the brake lines
You can change brake light switches on a Seat Toledo by first making sure that the engine of the vehicle is turned of. Then you can replace the old brake light.
where is the fuses for a peugeot 407
Take hold of the brake light switch and pull backwards. The switch will come out in the same way that you would unplug anything. Plug the new switch in
check little switch under your brake pedal....... and check brake fluid. This was the problem on daughters 206 . Topped up brake fluid on now ok.