0
Bolt size depends on how much load the bolt is to see in operation. The bolt size is chosen to be torqued, or pre-loaded, to a value that exceeds the expected maximum operational (or non opertaional survival ) load. Th epre-loaded value shou dnot exceed 50% of th bolt's ultimate strength.
For example say the bolt load in operation is calculated to be 600 pounds. You can choose a 10-32 staeel bolt rated at 1600 pounds strenght and preload it to 800 pounds by torque wrench. You need to convert torque ooald with standard formulas.
What else can I help you with?
Where can you purchase a bolt assy to a Savage Model 1905 Single Shot 22 Rifle?
As of 2014 one can purchase a bolt assy to a Savage model 1905 single shot rifle 22 at local gun retailers. Parts can also be purchased through Savage and local gun classifieds.
How do you remove interior door handle from 2001 GMC Sonoma pickup?
I believe the handle is one whole assy handle holder and lever. remove door panel and assy should rivet/bolt to door
Removing a 98 civic headlight assembly?
You need to remove the bumper cover in order to get at the lower bolt for the headlight assy.
How remove bolt 510 Remington?
Hey, you can try pulling back on the trigger while removing the bolt to the rear. Do the same to reinstall the bolt back in the barrel assy. I have a 514 and that's how it is done. Hope this helps . . . John <john.gro@gmail.com>
Can you install the bolt assembly from a 22 short Winchester Model 74 semi-automatic in a 22 LR that is otherwise identical and shoot 22 shorts in it?
It is possible, but you will loose all consistency and accuracy and it is potentiallty unsafe. I would recommend either trading in long rifle for a short missing the assy or trying to get a matching long assy bolt.
What can cause steering problems with the lower control arm assy bolt LH in Toyotas SEE Discuss?
its suspension performance will become low.
What is projection of foundation bolt?
The projection of a foundation bolt refers to the distance between the base of the bolt and the surface it is anchored in. This projection is important for ensuring that the bolt can securely attach to the structure it is supporting. The projection is typically determined based on the design requirements and load conditions of the structure.
Where is the tensioner for the serpentine belt on a hyundai entourage?
There are two Pulleys to the left of the alternator that have caps. Look at the pulley farthest from the alternator. If you look below this pulley, you will see (or feel) two bolt shaped structures. One is a bolt, the other is not a bolt. Attach a rachet to this bolt shape structure (not the bolt) and as you put pressure on this structure, the pulley will move.
Where is the alarm battery in a Volvo S80?
The battery is part of the alarm/siren assy, located within the rt frt qtr panel. Easily replaceable with a dremel tool to cut the security bolt.
How do you replace the power antenna assembly on a 1993 Seville?
pull trim back on right side of trunk unplg two connectors from ant assy 1 coax and 1 three wire connecter from relay unbolt ground cable get 94!! ant kit from dealer with adaptor connector un bolt two bolts holding ant to bracket pull ant down hars leave your old grommet in fender top and shove new ant into it grab bracket stock from kit align with bottom of ant assy and flange of wheel well just forwad of ant assy drill hole in flange and bolt bracket stock to flange. take two pair of pliers and twist bracket stock toalign a hole two one of the outer hole on bottum of ant assy. install 8mm head bolt through bracket into ant. mount hole and tighten connect three wire connector in to relay use the adapter cable to ant coax and plug into ant assy.
How do you loosen up a serpentine belt for a 1995 Ford Mustang?
As far as I am aware, there is no adjustment because they are a tensioner assembly. You can turn the assy by inserting a ratchet or wrench on the bolt or insertion hole to loosen tension.
How do you tighten a Polaris trailblazer 250 chain?
how do you tighten the chain on a 1999 polaris trailblazer 250 if the brake assy. is on the rear end then u need to loosen the 2 - 1/2 bolts on the bottom of the brake assy. and the to 5/8 bolts on the rear end then turn the part between the 2 5/8 bolt with a pipe wrench.
