0
If the plate height gets higher increase the depth of the birds mouth that sits on the plate. The birds mouth is the notch cut out of the rafter that allows it to sit flat on the top of the plate. If the plate is low then you will need to place a packer on top of the plate.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What are x-cut quartz crystals?
A plate of quartz cut with its major surface perpendicular to the x-axis
Which intaglio technique uses a burin to cut lines into a metal printing plate?
Engraving.
What are some plate holders called?
The most common type of plate holder is a thin rectangular sheet of woven fibers called a place mat. The mats are designed to place plates on to keep them from slipping around a polished table when the diner attempts to cut a food item.
To produce a recombinant plasmid and the foreign DNA are cut with a different restriction enzyme?
Fasle.
If meiosis goes does the number of chromosomes increase?
In humans they are cut in half. Its different for polyploidy.
Which cut provides a horizontal bearing surface for rafters?
The heel cut.
When putting up stub walls how do the corners get fastened togetter and where do they tie in?
Making sure we are talking about the same thing, I'm thinking you are in the attic and building a short wall on the sides to square up the slope of the attic? If that's the case just build the wall the height you want, cut the tops of the studs at the angle of the roof, rip a top plate with one side beveled the same, set it in place and nail to existing rafters. If the rafters are exposed, you can cut individual studs and not have a top plate. Snap a line so that they run straight.
What are the release dates for Hollywood Heights - 2012 Loren Doesn't Make the Cut 1-9?
Hollywood Heights - 2012 Loren Doesn't Make the Cut 1-9 was released on: USA: 28 June 2012
How to cut zoysia grass?
You should cut Zoysia grass lawns at heights of 1-2 inches above the soil line.
How do you place a napkin on side of plate - cut edge to outside or toward plate?
The edge should face away from the plate.
What are x-cut quartz crystals?
A plate of quartz cut with its major surface perpendicular to the x-axis
Types of Safety toe shoes?
These days safety shoes come in a big variety. Almost any type of shoe can be made with a toe cap. However the most common type of safety shoe is still the low-cut, leather upper, laced shoe. Type can be shoes, boots, rainboots, ... The closures can be laces, buckles, velcro, ... Upper materials can be leather, textile, synthetic, ... Outsole materials can be PU, rubber, TPU, ... According to different heights of safety shoes, it has low cut and mid cut safety shoes and high cut safety boots. For toe cap of safety shoes, it has metal toe cap and plastic toe cap. Metal toe cap has two kinds, iron and steel toe cap. For plate of safety shoes, it has metal plaste and kevlar plate. Meal plate also has two kinds, iron and steel plate. For more info of safety shoes, please refer to our web: www.credsafetyshoes.com
How do you cut diamond plate?
well first of all diamond can't be made into a plate because of a diamond is on a scale of 10 on the mohs hardness scale. Plus we dont have the weight or heat to cut a diamond UNLESS the machine is diamond tipped. You know the steel they make fire engine bumpers out of? That's diamond plate. To make a long story very short, how you cut diamond plate depends on what it's made from, but it cuts like flat plate does.
How do you figure time to cut grass by with of cut and seed of mower?
Cutting the grass gives you a beautiful lawn. It also tends to choke out weeds. Depending on the type of grass, you want to keep it between two heights to keep weeds under control. If you live in the South West and have a Bermuda Lawn, you want to keep the grass between 2 1/2 and 3 inches tall. You keep other grasses at different heights.
WHAT IS THE Name for the process in which printing is done from grooves cut into a plate?
Intaglio
How do you cut a 12 and 12 roof?
A 12 12 roof means 12 inches of rise for every 12 inches of distance across the width. The ends of the rafters would be cut on a 45 degree angle. Both ends. How long depends on the size of the roof.
What describes engraving?
Involves the use of a burin to cut lines into a metal plate
