0
How do you figure the equivalent length of ductwork fittings when calculating ac requirements?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How many fittings can you pick up on a one half inch copper line?
never heard of the fittings,now you can run 2 fixtures off that line,not fittings
How many gpm of water at 140 psi will flow through a 0.75 inch diameter pipe?
What schedule piping as schedule 40 fittings are rated for 125# thus your 140 PSI would be really dangerous to try on standard fittings
Does the 1998 Dodge Neon only have 1 grease fitting per side?
Yes, there are only grease fittings on the lower control arm ball joints one each side. It seems that some were delivered with these grease fittings and some just had thread plugs instead.
What kind of pipes are used for steam lines?
Heavy weight mild steel with screwed fittings bspt. == Normally galvanized pipes are not used for steam. Mild steel with screwed or welded fittings are the norm. Pressure and temperature are very important factors to be considered in what type of materials to be used. Steam even at low pressures can be extremely dangerous. Answer In hign temperature application nomally the alloy steel pipes are used ANSWER: Mild Steel Seemless pipes, thickness dependent on the pressure rating to be used.
Where are the lube grease fittings points for the 2004 Outback wagon since the service schedule requires it at 22500 miles?
There are no grease fittings on this vehicle. Most new vehicles especially those from Japan, now have sealed components that are prelubed upon the components assembly. This is done for the simple reason that the automotive market place is demanding a product that requires less servicing, resulting in a less expensive opperating cost to the consumer. These sealed components offer a good service life as long as the seals, ie. usually rubber boots, remain in good condition and are not damaged. Cheers!
What are pex fittings?
Pex fittings are used for making connections in PEX plumbing applications. Professiomnal plubmers used next type of PEX fittings: Crimp fittings, Clamp fittings, Push Up fittings, Sharkbite fittings and others.
What are the three alternative mechanical piping methods?
Compressing fittings, press fittings, and push-on fittings.
What do you call the fittings where the water enters the pool?
Return fittings
What does FTP in plumbing stand for?
Question is other way round FPT not FTP Female Pipe Thread FPT fittings are equivalent to "National Pipe Thread" (NPT) ones, but different from National Standard Free-Fitting Straight Mechanical Pipe Thread (NPSM) fittings.
What does AN stand for in fittings?
That is a term started in WW2 for nuts, bolts, fittings etc. to differentiate them from foreign fittings. It means Army/Navy.
Where are the grease fittings on a 2000 avenger?
There are no grease fittings, they are sealed units. If a part wears out the replacement part will have grease fittings if required.
How do you cement cpvc to copper fittings?
You can't you Do need adapter fittings
Are pipings and pipe fittings the same?
No, fittings go over the pipe
What is the difference between Wrought and forged Fittings?
The main difference between wrought and forged fittings is strength. Forged fittings are tougher than wrought fittings as they begin as a casting which is then forged which adds to its durability.
Boats typically have several metal fittings where ropes can be fastened What is the name for these metal fittings?
Metal fittings where ropes are secured are called cleats.
BOATS TYPICALLY HAVE SEVERAL METAL FITTINGS WHERE ROPES CAN BE FASTENED. WHAT IS THE NAME FOR THESE METAL FITTINGS?
Metal fittings where ropes are secured are called cleats.
How do you rectify leakage on pipe fittings threaded joints without removing the pipe fittings?
You cannot do that effectively without taking the fittings apart,
