0
How do you get panties that fak you these would have 1 or 2 dildos inside that would piston back and forth out of you while you were them?
Wiki User
∙ 12y ago
Ask in an adult sex shop for advice on this.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What does number forth mean?
"Forth" is not a number.
Is 1 forth the same as 4 percent?
No, 1 forth is the same as 25%.
What is seven and one forth plus ten and one forth subtract eight and one forth plus ten and one half?
19 and 3/4
Whats is one forth plus one forth plus one forth?
Three-fourths is one-fourth plus one-fourth plus one-fourth.
What is the difference between fourth and forth?
Fourth is like the number 4. Forth is to go forward.
A compressor that has a piston that travels back and forth in a cylinder is a?
It is simply a piston compressor.
Where is piston?
The piston is inside an engine, under the valve cover, under cylinder head. it is the piece that transfers the explosive energy into rotating motion along with the connecting rods and the crank shaft. It all however has to go through the whole drive train to get to the wheels: the the transmission,the drive shaft, the differential, and so forth. There is also a piston inside a typical brake caliper, sometimes more than one.
What is function of piston pin of a piston?
The piston pin joins the piston to the connecting rod. Igniting fuel / air mixture pushes down on the top of the piston, the piston transfers the force to the connecting rod, which in turn pushes against the crankshaft, converting the up and down motion of the piston to the rotary motion of the crankshaft. The piston pin allows back and forth motion of the connecting rod (as it's other end is moving back and forth in a circular motion with the crankshaft.)...if instead of a pin a solid joint was made from the piston to the connecting rod the engine would not be able to run, as the connecting rod would try to rock the piston back and forth (side to side, not up and down) as the rod was moved sideways with the crankshaft.
Differentiate between a reciprocating mortion of a cylinder piston and a rotary motion?
Rotary means going around, like in a Wankel. Reciprocating means going back and forth. like in a ordinary piston engine.
Why does a steam move back and forth inside a cylinder?
becuase its very small
To have kids how do you have that?
you put you're penis inside a womans vagina and go back and forth you ejaculate(cum) inside her and the sperm (cum) will impregnate the egg she has inside her
What is the use of tiller arm key in rudder stock?
A tiller arm is a tool to convert the axial motion of a piston into rotary motion of the rudder stock. Therefore, the design of the steering gears comprise a piston, which is moved by an hydraulic power unit in one axis back and forth, connected to the tiller arm. The tiller arm rotates the stock in starboard and port direction by the movement of the hydraulic piston.
How fast can a 50cc Honda ruckus go?
any 50cc bike will go around 30mph, that's why you can ride them at aged 16 (in the UK. There are ways to increase the top speed. - Big bore kit, this comes with a piston and increases the speed (although it will raise the 50cc to what ever size you decide to buy - stroked crank, this makes the piston go back and forth further, but increases the wear on the piston.
Why are connecting rods used in a car engine?
Con rods are used not ony in car engines, but in just about all piston engines. They're needed to turn the reciprocating(back-forth) motion of the piston into the rotary motion of the crankshaft. That rotation is then - via the gearbox, prop shaft etc what propels the car forward.
How do you put the rear disc brake cylinder back in the caliper after it is been accidentally pushed out on a 1996 Ford Taurus?
If it has come out completely, lubricate the disc brake piston and the piston bore (in the caliper) with clean brake fluid. Make sure the dust boot is clean and is seated in the caliper. Using a turning motion (back & forth), roll the lip of the dust boot over the piston and push the piston into the caliper by hand as far as you can go. You'll need a c-clamp and a block of wood (or an old brake pad) so that you can push the piston all the way into the bore. Go slowly as you are pushing and keep an eye on the piston so that it goes in straight with no resistance. You don't want to damage the sides of the piston. If the piston goes to the bottom with no problem, seat the dust boot lip into the piston groove. You'll have to bleed the brakes once the pads are in and the caliper is reinstalled.
What makes a mechanical fuel pump to pump?
A diaphragm inside that is moved back and forth normally by the crankshaft or cam.
Are Arctic wolves viviparous?
A wolf is viviparous, bringing forth live young that have developed inside the body of the parent
