0
Answer for USA, Canada and countries running a 60 Hz supply service.
Home owner big job
In the trade this is called a service stack. It is a complicated job in as much as you have to know wire sizes, ampacity of wires and proper electrical workmanship. Such a project should be left to a licensed electrical contractor to take out the proper permits and call for proper inspections. By taking this route it will leave you confident that if any mishaps happen to the installation down the road your insurance company will be behind you 100%.
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is an electrical service mast?
A service mast is attached to the building, it stands normally above the building or at the highest point of the building, were no one can get to it. The service mast contains the wires from the meter base to the top of the service mast, this is were the power company attaches it wires so that the building has electricity.
How do you install an outside electrical outlet in a brick and block house?
The first is taking power to a garden shed or other outbuilding, and the second is installing an outdoor socket outlet for your garden power tools.
What is an electric power sensor?
Electrical power sensors are used to measure characteristics of electric power such as voltage, current, power, and potential degradation of insulation due to age. For AC circuits, an electric power sensor can also be used to measure power quality. Some electrical power sensors are incorporated into transformers or other components of the power distribution grid. Others are added to existing systems. Typically, these electrical power sensors measure one or more physical characteristics and convert them to electrical signals. Basic electric power sensor categories include electrical capacitance sensors, electrical frequency sensors, electrical resistance sensors, and electrical conductance sensors.
Unit of electrical power named after Scottish inventor of the steam engine?
the unit of electrical power named after scottish inventor of steam engine is Watt ( the electrical power ) and the iinventor was James Watt
What unit is used to express electrical power?
Electrical power is also measured in Watts.
What is an electrical service mast?
A service mast is attached to the building, it stands normally above the building or at the highest point of the building, were no one can get to it. The service mast contains the wires from the meter base to the top of the service mast, this is were the power company attaches it wires so that the building has electricity.
Where do electricians work?
they work when there is any power fault in electrical equipment or install electrical equipment.
How do you install a power antenna mast or antenna on a four-door 1992 Acura Legend?
go to antennasRus.com buy the shaft and follow their easy instructions, I did it works great
The primary purpose of an electrical service drip loop is to prevent water from?
getting into the service mast
How do you replace power antenna mast?
how do I replace a power antenna on my jeep Cherokee 1992
How does a boat or yacht get electricity?
Normally the initial electrical source comes from a battery or series of. Some vessels have a sort of large power cord called a "shore tie". A great many vessels have generators of various size onboard to run electrical equipment. There are solar powered vessels and vessels that derive their power from small "windmills" on the mast.
Who can install a vanity light?
Most people can install an bathroom vanity light if the electrical box and light switch are already installed. You just need to make sure you turn of the power while you are installing the light and be certain that you are attaching the wires correctly. If you are not comfortable installing the light fixture on your own, or if you need to install the electrical box for mounting and the light switch, then you will need to contact a licensed electrician to install it for you.
What Electrical motors convert what power to what power to power?
Electrical motors convert electrical energy into mechanical energy.
How do you install an outside electrical outlet in a brick and block house?
The first is taking power to a garden shed or other outbuilding, and the second is installing an outdoor socket outlet for your garden power tools.
What does the DID stand for in DID Electrical?
"deliver, install,demonstrate"
How do you remove powered antenna mast from Mitsubishi Eclipse?
I removed the entire power antenna assembly and could not find any way possible to separate the mast from the motor assembly. Odd, since Mitsubishi sold me an antenna mast.
Why you install capacitor bank in electrical room?
Capacitor banks are installed in the electrical room to improve the power factor which is related to the inductive load caused by motors etc . The capacitors create a capacitive load which subtracts against the inductive load thereby improving the power factor. Most power utilities have penalties when your power factor drops below a certain value.
