0
What else can I help you with?
Fill in the missing fractions on the number line1- - - 2?
-1
If input is asdfghjk then the output is kasdfghj?
line = raw_input("Enter the plaintext") line1=raw_input("Enter the plaintext ") line2=raw_input("Enter the plaintext ") split =len(line)/2.0 split=round(split, 0) split=int(split) line = line[split:] + line[:split] line = line.replace("E", "o") line = line.replace("O", "e") line = line.replace("YAR", "ray") line = line.replace("RAY", "yar") split =len(line2)/2.0 split=round(split, 0) split=int(split) line2 = line2[split:] + line2[:split] line2 = line2.replace("E", "o") line2 = line2.replace("O", "e") line2 = line2.replace("YAR", "ray") line2 = line2.replace("RAY", "yar") split =len(line1)/2.0 split=round(split, 0) split=int(split) line1 = line1[split:] + line1[:split] line1= line1.replace("E", "o") line1= line1.replace("O", "e") line1= line1.replace("YAR", "ray") line1= line1.replace("RAY", "yar") print line.lower() print line1.lower() print line2.lower()
What were the Romans famous forit went in straight line1?
they were famous for building roads that went in a straight line (how weird!!!)
Average of 5 numbers in assembly?
.model small .stack 100 .data line1 db 03,12,15,14,01 avg db ? .code mov ax,@data mov ds,ax lea si,line1 mov cx,0005h mov al,00+1 l1:add al,[si] inc si loop l1 mov ah,00h mov bh,05h div bh mov [si],al mov ah,4ch int 21h end
What is the LED status in Tellabs 8110 Modem?
When power and line1 led is glowing modem status is OK when power and Pma led is glowing that means local lead is break. when power and pma is glowing but line 1 is blinking that means earth in local lead
Do Both tanka and haiku have specific rhyme scheme?
haiku has a pattern of 5syllables on line1 7syllables on line2 5 syllables on line3 Tanka has a pattern of 5syllables on line1 7 syllables on line2 5syllables on line 3 7syllables on line 4 7syllables on line 5
If building is serviced with 480 volts and you put a meter between ground and hot what will be the reading?
For alternating current, and assuming the supply transformer is properly grounded, you will have 240 volts to ground. 480 volts; single phase will have Line1 and Line2, both with 240 to ground and 480 across both Lines : three phase will have Line1, Line2, and Line3, all will have 240 to ground, and 480 across any two Lines. Same is true for 240 volt service, 120 to ground and 240 across. 120 volt service is 240 volt service using ground as neutral.
What is phone line 1 and phone line 2?
Phone lines using the RJ11 jack (the phone jack) have 4 wires...Colors of those are black yellow red and green. The Red(tx) and Green(rx) are for LINE1 (which is the primary phone number, usually) The Yellow(Tx) and Black(Rx) lines are for LINE2 (Which is for the secondary phone line, which most Phone services do not include in their standarized packages).
Can someone help you find what type of poem this is called info below?
where the type of rhyme goes: Line 1 & 2: Both the end words rhyme Line 2 & 3: Both the end words rhyme E.T.C Until; On the Last 4 lines: Line1 rhymes with Line 3 & Line 2 rhymes with line 4 ___________Rhyme1 ___________Rhyme1 ___________Rhyme2 ___________Rhyme 2 ____________Rhyme3 __________Rhyme4 ___________Rhyme3 ____________Rhyme4
What equates to about 500 pages of text?
Assume:55 lines per page80 characters per line1 byte of data per character(500 pages) x (55 lines/page) x (80 char/line) = 2,200,000 charactersAt 1 byte per character, that's2 MB plus 95 KB. (rounded)
What does L1 mean?
This word stand for Line1 <<>> On electrical equipment the terminal L1 is where the placement of the supply conductor is terminated. On three phase equipment, the terminals are identified as L1, L2 and L3. On an electrical magnetic contactor these terminals will be located on the top of the device. The terminations on the bottom of the device where the load is connected are designated T1 and again for a three phase equipment the designation would be T1, T2 and T3.
How would you make a patch cord to go from a 220V 30-amp 4-wire generator to run a 220V 20-amp 3-wire portable compressor?
To make a patch cord for this setup, you will need a 4-prong 220V plug that matches the generator's outlet, a length of appropriate wire rated for 30 amps, properly sized for the distance between the generator and compressor, and a 3-prong 220V plug that matches the compressor's inlet. Connect the wires according to color-coded standards (red and black to the hot terminals, white to the neutral terminal, green to the ground terminal). Make sure the wire gauge matches the amperage rating to avoid overheating.
