0
How do you re-wire a 230 volt 15 amp air-compressor motor with the twist-lock cord end missing?
Wiki User
∙ 12y ago
Obtain a plug body matched to the receptacle being used to supply power.
In all probability, you have a 3 conductor cord, 2 line conductors and a ground. Color of the line conductors may be black/red or black/white. Green is always ground. Connect the line conductors to the line terminals (orientation is irrelevant), and the ground.
If a 4 conductor cord, black, red, white, and green conductors. black/red will be line, white neutral (probably unneeded) and green ground.
Other variables may be considered if the question were expanded to include more information.
<<>>
The cap end that you are looking for is a classification of 2 pole 3 wire grounding, 250 volt. Its designation is a L6-15P. The 230 volt supply goes across the terminals X and Y with the green ground wire going on the G terminal.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Can you rewire a mixer 120 volt motor to run a 220 volts?
No, you will need a commercial mixer for that.
What will cause electric motor to shock you when you touch it?
The motor winding has gone to ground internally. The ability of the motor to shock you is caused by the ground wire missing or not connected. It is this ground wire that trips the breaker in short circuit conditions and disconnects the motor from the distribution system.
How do you rewire a 220 volt motor to run as a 110 volt motor on a old Howell electric motor?
Determine which leads are run leads, and which are start leads, or which are a combination of both. Once determined the overall solution is to parallel the windings externally, where at a higher voltage 1 motor lead per line is used, 2 would used per line in parallel. Leads marked 1 through 4 would be connected 1 to line, and 4 to line with 2 and 3 electrically connected and isolated as a series connection for the higher 220 single phase voltage. Rewire or reconnecting if possible to 110 would then be connected motor lead 1 and 3 to one of the 110 volt lines and the remaining motor leads 2 and 4 to the other 110 volt line. In some cases the parallel connection could be 1 and 2 to line, and 3 and 4 to line for 110 volts. It makes no difference on an induction single phase motor which line from the 110 either hot or neutral is connected to either pair of motor leads.
What property does not apply to a motor?
Which property does not apply to a motor?
A motor neuron and all the muscle cells that is stimulates are referred to as a motor and plate?
false, it would be a motor unit.
Can you replace a 110V hospital bed motor with 220V motor?
Yes, if you rewire the bed and rewire the plug on the wall to 220 volts.
Will a 96 ' 4.6 T-bird motor fit a 99' F150 extra cab with a 4.6 motor?
Yes the Motor will fit if you pull out the Ford motor. (It is Quite hard to rewire)
Can you rewire a mixer 120 volt motor to run a 220 volts?
No, you will need a commercial mixer for that.
How do you convert or rewire a 20HP 3 phase motor to single phase motor?
The winding design of the motor will not economically allow this to work. You would have to drive a 3 phase generator to supply it.
Is sae 30 non-detergent oil the same as motor oil for a car?
No. Do not use in your car. It is for use in some lawn mowers and aircompressor motors.
You have a 1983 cr60r it has no gears took the clutch cover off checked in there removed the cutch checked the gears there it moves freely just wont catch inside the motor?
rewire gear coords rewire gear coords
Is there a way to rewire a 5hp 3phase motor to run off of 240v without buying additional equipment?
No, you only have phase a and b. The motor will run as smoothly as a 3 phase motor that has lost a leg of power. That is if the motor is designed for 208v in the first place. Not a good idea.
How can you rewire your 220 volt motor to run on 120 volts?
If a motor is designed to run on different voltages there will be a wiring diagram on motor plate for 120 volt wiring. If not you will have to use a step up transformer to convert 120 V to the higher voltage.
Will a petrol primera starting motor fit a diesel primera?
Yes but it will not bolt straight on, you will need to modify the bolt holes and you might need to rewire the plugs.
Will a motor fro 2001 diesel 2500 sport 2wd fit in 2005 3500 4wd?
It would bolt in place, but you would have to rewire the entire truck to get the computer to work and the engine to start.
How did marita from n-dubz die?
Motor Bike Accident , It Explains It In The Song (Missing You )
How can you terminate a 3 wire wye motor to a 3 phase delta connection?
To terminate a 3 wire wye motor to a 3 phase delta connection you need a 3 phase transformer to convert from delta to wye. Do not lift the common neutral connections inside the motor and rewire for delta, because the voltages will be wrong.
