0
Are you asking about a wheel stud or exhaust stud, please clarify
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is 44x44 plus 4x4?
44x44= 1936 4x4=16 1,936+16=1,952
Factor 4x4 plus 1?
4x4 + 1 = (2x2 - 2x + 1)(2x2 + 2x + 1)
What is the exponential notation for 44?
for 4x4
What is an answer to a 4x4 magic squares with 10-5 numbers?
swer in a 4x4 magic squares with 10-=25 numbers in each column?
Using four fours how can you get 10?
(4x4)-(4+4sqr) (4x4)=16 (4+4sqr)=6 16-6=10
How do you replace rear broken wheel stud on 1991 Toyota 4x4?
The hub will need to be removed and the stud pressed or drilled out to be replaced.
How do you replace a broken wheel stud on a 96 4x4 Nissan pickup?
Notice there are two threaded holes in the brake drum. Insert a metric bolt into the holes and tighten until the drum pops off. Replace the stud.
Should I replace the fuel filter for the 1985 Ford 150 4x4 XL?
Yes, replace it every 50,000 miles.
How do you replace a wheel bearing on a 1988 ford f-150?
Front or rear?? 4x4 or 4x2??
How do you replace the oil pan gasket on a 2000 ford F-150 4x4 5.4L V-8?
chachange oil pan gasket 1998 ford f-150 4.6 L 4x4
How do you remove the front rotor on a 1993 F 150 4X4?
How do you remove a front rotor on a 1993 F 150 4X4
Why is the front end on my 2000 ford f-150 4x4 squeaking?
Replace upper and lower ball joints. Not hard, but time consuming.
How do you replace a front shock on a 1979 ford f-150 4x4?
vise grips and a hammer and a torch maybe some c4 aswell
How do you change the lug stud on a front wheel of a 1988 Toyota pick up truck 4x4?
You should be able to unscrew it and replace it. Some pointers are to coat the stud in PB blaster or liquid wrench and let it sit. Then thread two nuts onto the stud, tighten them against each other and wrench on the inside nut to try and loosen the stud. You can also try a big pair of vise-grips.
Can you fit diff locks to a 4x4 mj bedford?
I believe the TM 4x4 has diff locks and has the same 10 stud axles. maybe someone can confirm this
How do you replace broken stud on 2001 silverado 4x4 z71?
need to know where the stud is and what it is fastening.... soak it overnight with liquidwrench or mystery oil, then use vise grips. If stud is broke off flush, drill and use an ez-out. Be ABSOLUTELY CERTAIN that you soak it first!!! I think you are talking about a wheel stud? If it's 4wd spin the hub assembly until it lines up with the holes in the back of the assembly (this gives room to pound it out). Next find a 5lbs short sledge hammer. Make sure the hub won't spin and pound the stud out. To install the new stud put it through the hub hole and get it started. Place washers over the other end and also the lug nut. Tighten the lug nut and as it puts pressure on the washers it will pull the stud through. -Hope that helps-
What is causing front end creaking noise on a '98 s10 pu 4x4 zr2 package?
well on my 01 zr2 blazer. its because it has a broken wheel stud on the left front. i don't know if that's your problem but that definatly makes the creak.
