0
What else can I help you with?
What is the difference between slip gauge and angle gauge?
slip gauges are the end standard devices used to measure length. angle slipgauges are used to measure angles . both of them can wring with each other .. and evrything is same : )
What is the degree of a ray angle?
If I understand the question correctly, then 0 degrees or 180 degrees.
Line PQ is the angle bisector of angle APB and the measurment of angle APQ equals 107?
hmm... i am not sure I understand what you are trying to ask?An angle is formed by two rays with a common endpoint. The angle bisector is a ray or line segment that bisects the angle, creating two congruent angles. Therefore angle QPB is the same as APQ.
What is the rule for a reflection?
When a light ray hits a surface at an angle (called the angle of incidence) and all or part of it is reflected at an angle (called the angle of reflection), the law of reflection states: the angle of reflection equals the angle of incidence. The angle is measured from an imaginary line drawn perpendicular to the surface at the point the ray hits the surface. what the hecka i dont understand this crap i hate math
How do inscribed angles help you understand angles that occur outside the circle?
why dont the central angle change regardless the size of the circle
Explain the technical terms of a slip angle?
the angle relative to the wheel and chassis turning around corners
What is the difference between slip gauge and angle gauge?
slip gauges are the end standard devices used to measure length. angle slipgauges are used to measure angles . both of them can wring with each other .. and evrything is same : )
What is difference between slip gauges and angle gauges?
slip gauges are the end standard devices used to measure length. angle slipgauges are used to measure angles . both of them can wring with each other .. and evrything is same : )
Why is it important to put the cover slip on the slide at an angle?
Placing the cover slip on the slide at an angle helps to prevent air bubbles from forming between the specimen and the cover slip. Air bubbles can distort the image and hinder proper observation under a microscope. Placing the cover slip at an angle allows for a more even distribution of mounting medium and helps to minimize the presence of air bubbles.
Why the handle of a hammer is not uniform in cross section all the way?
A hammer handle is contoured so that your hand will not slip as easily when you are hammering.
Why is it useful to have more than one way to name an angle?
It makes it easier to understand which angle you are talking about.
What is the schmid factor?
The Schmid factor m is part of the equation for the critical resolved shear stress τ0. The critical resolved shear stress is the component of shear stress in a slip plane, resolved in the direction of slip, necessary to initiate slip in a grain (plastic deformation in metals). m = cos(κ)cos(λ) ; τ0 = mσ κ - the angle between the applied load direction and the slip plane normal. λ - the angle between the applied load direction and the slip direction. σ - the applied stress or load
How can you find the coefficient of friction force only given mass and theta?
The coefficient of friction is the tangent of the angle theta where the angle is measured from horizontal when the mass first starts to slip
What is the measurement of an exterior angle of a pentagon?
Assuming I understand your question, the exterior angle of a regular pentagon is 72 degrees
What sort of non-slip floor tiles are currently on the market?
I completely understand the need to have non slip flooring. There are products that you can purchase to coat your floors to make them non slip, but if you are looking to install new flooring, I would highly suggest cork flooring or rubber flooring which both are guaranteed to be non slip.
For every angle is there only one angle bisector?
hmm... i am not sure i understand your question, sounds like a yes!! The bisector of an angle is the line or line segment that divides the angle into two equal congruent parts. The angle bisectors meet at the incenter to bisect the angle.
What is valve angle?
www.chevyhiperformance.com/techarticles/89678_valve_angles/index.html You should have a good understand with this.
