0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What shape has 2 parallel sides and 2 not parallel?
A rhombus.
What is the parallel slope of 2?
A parallel slope to 2 is 2. A perpendicular slope to 2 is (-1/2).
What has 4 sides two sides are parallel and 2 are not?
A trapezoid has 2 parallel sides and 2 that are not.
Does a cone have atleast 2 congruent parallel bases?
No but a cylinder does have 2 parallel bases
What shape has 2 or more parallel sides?
A square has 2 parallel sides!! You dumb dumb!
Will a 540 Watts x 1 RMS 4ohms Amplifier be suitable for a sub rated at 380 watt RMS with 4ohms plus 4ohms dual coil?
The problem you have there is that your sub woofer needs both coils wired and your options with that setup is either 2 ohms or 8 ohms depending on if you wire the sub itself in series or parallel. If you use a second sub like the first one and wire both subs in parallel and then wire the two subs in series you can achieve 4 ohms. You could also wire the subs in series ( 8 ohms each ) and then wire them in parallel to achieve the overall 4 ohms.
How do you wire 4 dual 4 ohm coils subs to one ohm mono?
If you wire all 4 coils parallel, you get 1 ohm (mono).
2 ohm stable amp can you wire up your four 4 ohm svc speakers too 2 ohm?
I think if you have 2 subs, you have to wire them in parallel so they are both loaded to 4 ohms, then the amplifier will see a 2 ohm load. what amp are yu using? im planning on getting a 2ohm stable class d mono amplifier for my 4 ohm DVC Subs. You need to wire both positives to one positive input and both negatives to one negative input for parallel wiring. That's what ive learned. Since your amplifier is stable at 2 ohms, you shud get a lot of power.
Dose a 1000 watt 1 ohm stable amp work for my dual 2 ohm L7 12s?
yes but make sure the rms power for each is the same or close at 2 ohms and wire both subs in series-parallel
What is the best way to wire your subs to get the most power?
You get more power by wiring the speakers in parallel, but you need to verify that the amplifier can handle that configuration or you may blow the amp.
If 2 4 ohm subs were wired in series 2 equal an 8 ohm setup n you wire that in Parallel with another 4 ohm would it put out a 2.6 ohm load?
Yes, just make sure your amp can run at 2 ohms and you're fine.
What gauge wire do you need for 1800 watt amp and 2 550 watt subs?
4 gauge
What is the best way to wire 2 svc 2 ohm subs with a Rockford Fosgate T500 1db?
How much power can the subs take in terms of RMS wattage? You can either wire them to a 4 ohm load where they will each see 125 watts, or to a 1 ohm load where they each get 250 watts. Rockford Fosgate supplies a very useful feature for showing how to wire the subs for the impedance that you want: http://www.rockfordfosgate.com/rftech/woofer_wizard.asp
Will two 4ohm subs running series and one 8ohm sub running parallel work together maintain a 4 6 or 8 ohm load if not how will the subs work together with a single monoblock amp?
4 Ohm subs wired in series gives an impedance of 8 Ohms. 2 4 Ohm subs wired in series, wired with an 8 Ohm sub in parallel gives you a final impedance of 4 Ohms. Speakers wired in series raise impedance, speakers wired in parallel lower impedance.
Can you hook up 2 1700 watt mono block amps to your 4 12 inch pioneer subs that max out at a 1000 watts?
Yes you could do that but to keep from blowing out your subs you're probably going to have to turn your gain down on your amps. Also keep in mind if you wire these parallel you'll be at 2 ohms so your gain will probably need to be closer to the minimum setting than the max.
If 2 dual 4 ohm subs were wired in series parallel what would it put out?
The final impedance would be 4 ohms.
Why after buying a new CD player when the radio is on would the subs work but when you put in CD the subs do not come on?
make sure amp remote wire is connected to p.cont wire and not power ant wire on the radio
