0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How many edges does a rhombic dodecahedron have?
24 edges.24 edges.24 edges.24 edges.
How many edges does a pentagonal prism have?
A pentagonal prism has 15 edges. 10 of these are base edges and then 5 lateral edges. Formula : A prism with a n-sided polygons at each end will have 3n edges.
How many edges does a cuboid have?
a cuboid has 12 edges
How many edges does a rectangulr prism have?
12 Edges is how many edges a rectangular prismhas
How many edges does a rectangle have?
4 edges A rectangle has four edges. A rectangle has 4 sides but no edges which are normally applicable to polyhedrons.
How does amplitude change in a drum?
I dont think how far my answer is correct but, the amplitude of the sound produced at the centre of the drum is more when compared to its edges. this might be due to the tension in the leather surface of the drum and the law of vibrations.ie, towards the centre where at a particular point when moving away from the edges of the drum vibrates more than at edges. Here, the force of the stick( if a stick is used) with which the sound is produced must also be taken into consideration and also the make of the material with which the sound is being produced.
If I had a Drum with a stamp that says Champion on it was Champion a Sonor made drum model?
Yes, Sonor Champion was a drum model back in the 70'. 6 ply beechwood shells, with rounded bearing edges.
How do i attach the skin on the drum on last king of Africa ds game?
Hi there, You attach the skin on the drum by circling the stylus around the edges and eventually it will hold.
What is a bearing edge on drum shell?
It is the surface of the drum shell that actually touches the drum head. The area of this surface is less than that of a cross-section of the whole shell, since it is created by making an angled cut into the shell around the rim. The thickness or thinness of the bearing edge affects the tone of the drum; finer or sharper bearing edges yield a brighter tone, while thicker bearing edges yield a warmer tone. If the bearing edge is not perfectly level and perpendicular to the cylinder of the shell, the drum head will not seat properly and the tone of the drum will suffer.
How do you put drum brakes back together on an 01' tracker?
To put drum brakes back together on a 01 Tracker, put together drum brakes by the edges. Spray with penetrating oil. Finally, tighten the bolts and lug nuts.Ê
What part of the drum is the highest?
the top of it i think hop its helps im not thatgood
How do you free frozen brakes on a car that sat for a few years?
Remove tire and beat drum w/ a large rubber mallet. If this does not work use hammer or sledge around edges of drum - don't hit too hard.
How do i take the rear brake drum off my 89 ford probe.?
Remove the rear wheel, and the drum will slide off, unless its been there for a while, then you may have to tap around the edges with a hammer, and be sure you dont have the e-brake set, or you wont get it off.
How can you clean a copier drum?
The drum in your Canon business copier, which is a part that works hand-in-hand with the toner cartridge, is susceptible to dust and dirt. A dirty drum transfers debris onto paper, resulting in dirty copies and documents containing missing words and graphics. Your Canon copier may also imprint streaks of toner around the edges of copies. When cleaning your Canon copier_¾_s drum, do not use a liquid cleaning solution, water or an abrasive towel to remove the debris. These substances not only damage the drum but also your copier.
How do you get the brake drums off of a 1997 Mercury Tracer?
Remove the tire, there should be 2 phillip head screws that need to be removed. If u can not pull the drum off by hand you will need a hammer to knock the drum loose. Hit the front of it a few times, them around the edges, that should free it. Good Luck.
How can drums be controlled?
Drums are controlled in Guitar Hero by hitting the drum pads and cymbals with the provided drumsticks. You can use other sticks as well, if you want, all you have to do is hit the pads with them. Don't hit them too hard, or you will break the sticks. You should also try to hit the center of the pads, and not the edges, the drum pad sensors are built to receive the center first, then the edges. Also, don't forget to plug in the cymbals to the little micro-mini jacks on the cymbal stands.
How do i remove the rear drum from a 2006 Toyota sienna?
Make sure parking break is off. There are two small screw holes in the drum. Go to an auto parts store and get a selection (two each size) of metric bolts that are close to that size. Find the ones that fit and hand start one in each hole. Bolts should screw in easily. screw in bolts until tight with a wrench and tap lightly on the the drum on the outside edges going all the way around. You may need to do this retighten and tap again around the drum. This should loosen the drum from the rear axle plate.
