0
This depends on the axle rating on the trailer...most likely a 5X8 has a light duty axle wich is less than 2000# but may be less doesnt matter what size trailer a load is on,but the legal height for any load on any vehicle is 13'6" however,common sense would tell you if a load is to high for safe towing
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is MATCHED LOAD?
the matched load is aresistive load which at (Q=0)which generated from the generator mesur the load at( Ql=Qc)and at it we get high efficancy as losses of T.L P1=mesured P2=(3^.5) V2I2cos fai delta p=p1-p2 eff=p2/p1*100>>>>>>high
What is the percentage of the no-load current in a transformer to its full load current?
2 to 5% of full load current
Why high voltage is kept open in open circuit and low voltage is shorted in short circuit test?
In Short circuit test High Voltage side is feeded with 2-5% of the High Voltage rating to circulate approximately full load current in low voltage winding by short circuiting it. Low voltage is generally short circuited to facilitate measurements because it is more difficult to measure the quantities at high voltages.
What is percentage of transformer loss at no load condition?
major component of power loss in a transformer is secondary resistance.when transformer is operated under no load,no current flows through the secondary.so under no load conditions transformer has just very small megnetic losses.
What is a potential divider and what does it do?
The most common type is resistive division. Say we have a source of V volts and we wish to apply a portion of the V volts (aV where a is between 0 and 1) to a load of resistance R. We can place a resistor R2 in series with load R to drop off the unwanted part of the voltage V. The math is a = R / (R + R2). This only works if the resistors are constant. For a changing load other methods are necessary. Say the load needs 5 volts and it draws 10 milliamperes at 5 volts, but the supply is 10 volts. The effective load resistance is 500 ohms. A 500 ohm resistor in series with the load would drop off the unwanted 5 volt excess. Suppose the load changes by 10%, but we wish to hold load voltage to 5%. We can place a 500 ohm resistor in parallel with the load and use a 250 ohm resistor to drop the voltage to 5 volts. The voltage change is now only 5% for a 10% load change.
Utility trailer that is 5' X 8' ft The axle is 59 inches from the front of the trailer not the coupler You want to extend the back of the trailer 10 inches Would this be safe to do and pull a load?
On a 5' X 8' Utility Trailer you would want a 60% / 40% axle weight distribution for optimum towing/tracking of trailer. A design of 96 total inches in length would produce a 54" length from the front of the trailer to axle center. Adding an additional 10 inches to the rear of the trailer would then produce a optimum 63" length from the front of the trailer. Extending this trailer by 10 inches would fall into a safe range as long as you take into consideration the weight distribution of the load.
Can a 1994 Nissan pickup 5 speed 4 cylinder short bed pull a 900 pound utility trailer?
Why wouldn't it be able too ??
Can a 1994 Nissan pickup 4 cylinder 5 speed short bed pull a 900 pound open utility trailer from uhaul?
yes, but they wont let you
Can 5 X 8 Utility Trailer go on the Garden State Parkway?
I do not believe they are allowed on the section that goes into NY State and connects with the Tappan Zee Bridge approaches.
What is the most common size trailer hitch ball?
Depends on the size of the trailer. It could be 1 7/8" or 2" or 2 5/16". 2 inch is the most common size used. It is what is used for most single axle utility trailers.
What is the max weight that can be legally loaded on trailer?
All trailers have a weight limit that is stamped on the trailer somewhere. Normally it is stamped on the trailer tongue or on a data plate attached to the tongue or trailer frame. You can also determine the weight the trailer can handle by the diameter of the axle. Find your measurement in the following table of typical axle diameters: 1.5-inch diameter, 1,000 pounds 1.75-inch diameter, 2,000 pounds 2.375-inch diameter, 3,500 pounds 3-inch diameter, 6,000 pounds 3.5-inch diameter, 8,000 pounds 4-inch diameter, 9,000 pounds 5-inch diameter, 10,000 pounds Multiply the axle capacity by the number of axles to get the maximum load capacity for your utility trailer. Remember that no matter the capacity of the trailer you must have the correct trailer hitch in order to safely pull the trailer.
What is a matched load?
the matched load is aresistive load which at (Q=0)which generated from the generator mesur the load at( Ql=Qc)and at it we get high efficancy as losses of T.L P1=mesured P2=(3^.5) V2I2cos fai delta p=p1-p2 eff=p2/p1*100>>>>>>high
What is MATCHED LOAD?
the matched load is aresistive load which at (Q=0)which generated from the generator mesur the load at( Ql=Qc)and at it we get high efficancy as losses of T.L P1=mesured P2=(3^.5) V2I2cos fai delta p=p1-p2 eff=p2/p1*100>>>>>>high
What are the four most essential utility programs?
1 defragmenting utility 2 anti-virus utility 3 time utility 4 date utility 5 copying utility
What are 5 examples of utility software -?
5 examples of utility software are:Tuneup UtilityAdobe Flash playerMcAfee Virus ScanWinRARWinZIP
If there is not a jaws 5 then who made that trailer?
It's probably a fan made trailer.
What are the release dates for Trailer Fabulous - 2005 5 1-5?
Trailer Fabulous - 2005 5 1-5 was released on: USA: 24 August 2005
