0
By asking this question you are probably not quite ready to take on this particular task. The correct answer to your question will depend on the exact site location of the light switch and the of the light it is controlling.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed. Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Is the pressure switch high Normally open or normally close?
A pressure switch can be normally open or normally closed. It depends on how it was made. The NO/NC should be marked somewhere on the switch. A pressure switch can be normally open or normally closed. It depends on how it was made. The NO/NC should be marked somewhere on the switch.
Why is the main switch connected in series together with the rest of the circuits in the house?
It is connected so that it can disconnect the entire power grid in the house with one switch. This switch is usually integrated into a circuit breaker. No matter how one looks at it, this switch must be made to withstand (and be able to switch) great currents (in excess of 16A) at relatively high voltages (120V/230V). Special care must be taken during the design phase, as the switch will most likely have to suffer severe arcing as well as heating, during normal operation.
How can you wire and control 3 lights from 1 switch?
This is simple. First the wire coming from the power supply go to the switch. Then it goes to the first , the second and the third light. Since the switch comes first all three light will be controlled by that one switch.
Why do ceiling fan lights go out?
Without knowing some more facts, there could be several different answers to explain why a ceiling fan's lights "go out":someone has turned them off at the switch for the lights on the fan unit;the light bulbs are "dead" and need replacing because their filaments have broken;there is a fuse protecting the lighting circuit and it needs replacing because it blew from the surge of high current that sometimes happens when a light bulb "dies";there is a timer in the fan unit which turns the lights off after a certain period of time;the wiring from the switch to the light has become disconnected;the switch in the fan that controls the lights is broken and needs to be replaced...
To moderate the high voltage of currents entering a house from power lines a is used?
transformer YES but transmission is 475kv and distribution is 16kv and finally one phase out of a transformer on a pole or on the ground. An electric switch yard will have transformers to reduce to distribution voltage.
Why do interior lights stay on constantly on your 1999 Tahoe?
The dimmer switch has a setting which turns on the dome light. Just after turning it to high you should be able to 'click' it into the position required for the interrior lights. The dimmer switch has a setting which turns on the dome light. Just after turning it to high you should be able to 'click' it into the position required for the interrior lights.
How do you replace the reversing light switch on a Peugeot 306?
The reversing light circuit is controlled by a plunger type switch screwed into the top of the transmission casing. First check that the fuse has not blown. To test disconnect the wiring connector to the switch use a multimeter resistance should be high but when reverse is selected should be low if on buzzer mode the meter should buzz. If no buzz switch is broken if buzzing look for a wiring connection that is broken because the switch is ok.
What is the multifuntion switch on a 2006 PT Cruiser?
It is the combination turn signal, high beam, head light switch.
Where is the fog light switch on a 1996 Chrysler sebring convertible?
On the turn signal indicator arm. Switch on the headlights, make sure the high beam is off, then pull out the rotating light switch.
Where is dimmer switch on 2000 Dodge Caravan?
The headlight high/low beam dimmer switch is part of the turn signal switch.The dash light dimmer is next to the headlight on/off switch.The headlight high/low beam dimmer switch is part of the turn signal switch.The dash light dimmer is next to the headlight on/off switch.
Taurus high beams stay on all the time they will not shut off even when the key is off also dome light stays on ocassionally when it should not?
If you have a Ford Taurus and the high beams stay on all the time, chances are that you have a defective control switch. The dome light uses a separate switch but is likely to have the same problem. To correct the problem, both switches should be replaced.
Where is high beam switch location on 1977 corvette?
It is on the signal light switch. Pulling it toward you will change from High to Low beam lights and vice-versa 7T77T7
Why do Low beams on VW Beetle not light up but high beams work?
Check the bulbs and then the multifunction switch (headlight switch)
Daytimelamps low beams not working high beams are replaced bubls relay switch and turn singnal light switch what could the problem be?
Have you checked the daytime running light module?
Your high beams switch is broken in your 2001 Honda accord how can you fix it?
If the high beam switch is broken that it should be replaced. When the unit is replaced the high beams will work again.
How can light house be identified at night?
a light house is on the coast of any body of water, has a huge yellowish white light that slowly turns and if fairly high up.
Should you switch on your high beam lights in city traffic?
Never!
