0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the weight of a steel plate that is 1half inch thick 20 wide inch and 45 inch long if the steel weight .28 lb per cubic inch?
The volume of the plate is (0.5 x 20 x 45) = 450 cubic inchesThe weight is (450) x (0.28) = 126 pounds
How much weight will a four inch tall X 2 inch wide with a one quarter section steel tube five foot long supported on both ends hold in the middle without bending?
That depends... on the composition of the steel !
How do I find the weight of an 8 x 12 rectangular section of steel that is 20' long?
8 inch x 12 inch solid? If so, then volume = 8/12 ft. x 1 ft. x 20 ft. = 13.3333.... cu.ft. Steel is ~ 490 pounds per cu.ft. 490 x 13.3333.... = ~ 6533.33 pounds.
How long is an eighth of an inch?
If you can draw a line 1 inch long and divide it into 8 equal parts, then each of the segments would be an eighth of an inch long
Is there something 1 inch long?
A small eraser is about one inch long.
Is it possible to drill a three inch hole through three 2x10's?
i would use a long shafted hole saw
Description of a drill bit?
A piece of steel rod about 4-6 inches long, with a flute cut in one half, ending in a point. Various thicknesses from 1/16 to 3/4 inch.
Can you drill cast iron with a dimon bit?
You don't need a diamond bit. High speed steel will do as long as you drill slow (about 400 rpm) and keep the tip lubricated with cutting oil.
How do you drill through a wall with a drill bit that is too short?
(trick question? find a more narrow wall.) They sell drill bit extensions - metal rod. OR measure carefully and drill from the other side. Or find a drill bit that is long enough.
How do you save a split tree?
You can try, there is no guarantee that it will work. Use a come along, a doubled cable with a ratchet, to pull the split together. Get a piece of 3/4 inch all thread long enough to go through both trunks. All thread is like a long bolt that is threaded the entire length. Drill a hole through both trunks, insert the all thread and put a large washer and nut on both ends and tighten the nuts until the split is tight together. Cut off the extra all thread. If the tree lives, it will heal over the bolt and the split. Depending on how big the tree is and your access to a large drill and bit, you may want to have a professional do this. If you want to do it yourself, you can get drill bit extensions in 18 and I believe 24 inch lengths. It will take a little time, but a 3/8 or 1/2 inch home drill can get through the tree a little at a time.
How do you make a homemade knife holder?
get 2 pieces of steel 4 inches long and a inch high and 1 piece of steel 3/4 of a inch tall and 3 inches long and some nut and bolts and drill 2 holes in the to bigger steel pieces at each end and one at the smaller piece end and bolt it up and sharpen it to get it a little sharp then use a stone
What is the weight of a steel plate that is 1half inch thick 20 wide inch and 45 inch long if the steel weight .28 lb per cubic inch?
The volume of the plate is (0.5 x 20 x 45) = 450 cubic inchesThe weight is (450) x (0.28) = 126 pounds
What is the diameter of pinewood derby axle nails?
Pinewood derby axles are one inch long, 0.087 inch diameter zinc plated steel nails.
How much weight will a four inch tall X 2 inch wide with a one quarter section steel tube five foot long supported on both ends hold in the middle without bending?
That depends... on the composition of the steel !
How do you drill out stock 2007 flht exhaust baffles and do you have to remap and how do they sound drilled out?
You can take a LONG steel pointed rod and punch out the baffles. The You don't have to remap or do anything. It sounds slightly louder..a nice sound and the throttle response increased from a ded stop. the baffles are not able to be removed since they're welded in place but you can drill them out or just punch through them.
How long does it take to drill and tap a rifle?
Drill and tap it for what?
How is oil extracted?
Oil is extracted through drilling a well into an underground reservoir, typically using a drill bit attached to a drilling rig. The oil is then pumped or flows to the surface through the well. Various techniques such as primary, secondary, and tertiary recovery methods are used to extract the maximum amount of oil from a reservoir.
