The required resistance is 12/1.5 = 8Ω.
Five 40Ω resistors in parallel have an effective resistance of 8Ω.
It is a digital circuit that produces the arithmetic sum of two binary number .It can be constructed with the full adders connected in cascade,with the output carry from each full adder connected to the input carry of the next full adder in the chain.
A parallel adder is a binary adder that can possibly form sum and carry the outputs for addend and augend words that operate on corresponding pairs addend and augend bits in parallel.
The basic idea of fault tolerance through redundancy is to size the system so that there is at least one more unit than the minimum required to carry the load. Thus, if a load is 10 amperes, a fault tolerant redundant system might have three (3) 5 ampere units in parallel;one more than is needed, hence: N+1 redundancy. The failure of any one power module leaves sufficient power available to support the whole load.
As far as I know, ALL waves carry energy.As far as I know, ALL waves carry energy.As far as I know, ALL waves carry energy.As far as I know, ALL waves carry energy.
There are occasions where the probability distribution function (pdf) has to be obtained empirically (experimentally). However, it is possible that it is expensive (in time or money) to carry out repeated experiments. In such a case, it can be useful to build a mathematical model that simulates the trial. Input random numbers and the model outputs the result of the trial. In this way it is easier to carry out repeated trials and so generate the required pdf.
Resistors in parallel work just like highway lanes in parallel. -- The more lanes there are, the more traffic they can carry. -- Any number of lanes in parallel are always wider than the widest single lane, and can carry more traffic than the widest single lane can. "wide lane" = low resistance "narrow lane" = "high resistance" "traffic" = "electric current"
1 resistor has 176ohm resistance (in paralel) ---> given current (I) = 5 A Potential difference (V) = 220 V total resistance = V/I = 220/5 = 44 let the number of resistors be x , 176/x = 44 x = 176/44 = 4 therefore the number of resistors is 4. :)
A binary parallel adder is a digital function that produces arithmetic sum of two binary numbers in parallel. It consists of full-adder combinational arrangement thus, the output carry from one full adder connected to the input carry of next full- adder.
It is a digital circuit that produces the arithmetic sum of two binary number .It can be constructed with the full adders connected in cascade,with the output carry from each full adder connected to the input carry of the next full adder in the chain.
Yes and no. The ripple carry adder is one type of parallel adder. Other parallel adder types include the pipelined parallel adder and the carry look-ahead adderamongst others.
The parallel adder which we use in the digital circuits ,the carry output of each full adder stage is connected to the carry input of the next higher order stage.therefore,the sum and carry outputs of any stage cannot be produced until the input carry occurs; This leads to a time delay in the addition process.This delay is known as carry propagation delay. to the second question the propagation delay can be avoided in the binary parallel adder with the help of look ahead carry generator .............................................................................................................................
can use 400mm THW,RHW,RUH (rating: 400mm = 388amperes)
A: Because both item are connected is series. Any resistance connected in series will carry the same current no matter of the resistance value or the number of resistors. However for an incandescence lamp the value will change when turn on and change when it is hot, That is because lamps have different property then resistance when cold and hot
The only reason i can think of this making sense is that it makes the calculation for total resistance easier. Other then that i can't see any benefit from having resistors with similar ratings. The formula for finding total resistance in a parallel circuit is Rt=1/1/r1+1/r2+1/rn... If all the resistors are the same, you can do the calculation in your head a lot easier.
In the state of Illinois, the employer is required to carry workman's compensation.
parallel side are side that keep going and never touch and two side which carry on forever
The tubes connected to the heart are the arteries and veins. Veins carry blood to the heart, and arteries carry blood away from the heart.