answersLogoWhite

0


Best Answer

It depends on where the sub panel is situated. If the panel is under the same roof as the main distribution panel then no ground rods are needed on the sub panel. If the sub panel is in a different building then a ground rod might be needed. There has been an electrical code rule change on this subject. Check with your local electrical inspector before installation so that it is done correctly.

User Avatar

Wiki User

8y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

11y ago

A minimumbare copper wire that can be used to ground a 200 amp distribution service is a #6.

This answer is:
User Avatar

User Avatar

Wiki User

14y ago

Two ten foot rods placed ten feet apart.

This answer is:
User Avatar

User Avatar

Wiki User

11y ago

2

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How many grounding rods are needed for 200 amp service?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Natural Sciences

Should one or two electrical service ground rods be used on a service distribution?

In Canada the requirement for grounding purposes calls for two 5/8" x 10' ground rods placed 10' apart. If rocky ground is encountered, then a grounding plate can be installed. The grounding plate dimensions are 10" wide x 16" long x 1/4" thick. They are galvanized coated and must be buried 24 inched below grade.


What do grounding rods do?

If allowed by local codes and regulations, grounding or earthing rods may be used for making safety protective grounding connections to any type of equipment including machinery, household appliances, metal pipework, etc.Whenever and wherever they are needed, grounding or earthing rods must be installed by driving them firmly and deeply into suitably prepared soil within the ground at the earthing point.However nowadays the latest National Electrical Codes and Wiring Regulations in most developed countries insist on using a system of safety grounding wires which are not connected to separate grounding rods installed for each piece of equipment. In that system the safety grounding wires must all be run back to the main circuit breaker panel because it is the main circuit breaker panel which is now the sole point of connection to the main safety earthing point for the whole building or site.Nowadays the main safety earthing point itself may or may not be an actual grounding rod driven into the ground because many codes and regulations now insist that the main safety grounding or earthing point must be made by a well-made connection to the grounded/earthed protective safety sheath of the electricity utility company's service cable coming onto the property, i.e. the site, home or other building. What is required depends entirely on the electrical codes and/or wiring regulations of each particular country.That system provides a better and safer way of providing protective grounding connections for equipment including machinery, appliances, metal pipework, etc.


Minimum length of a grounding electrode?

A standard ground rod is 5/8 x 10'. The amount of rods needed is governed by the electrical code. The largest type of grounding system is a Ufer ground. This is where the bare grounding conductor is embedded in the footings of the building and the weight of the building presses the ground wire to the earths surface. These types of grounds are used mostly in construction and are requested by electrical engineers.


How far apart do ground rods need to be?

Well the first grounding rod would be for the meter located outside the home and the second grounding rod would be for cox cable line.but but if you have dishnet work you will not need too. The NEC does not specify how many ground rods should be installed. I can only guess why but it is important to note that ground rods are SUPPLEMENTAL to a water pipe grounding electrode when a water pipe is your primary electrode. It is easy to think of the rod or rods as primary and the water line as secondary but this is not the case. Where I live the local jurisdiction requires 2, and the NEC does specify that when more than one is used they must be a minimum of 6 feet apart. Many times utility companies other than your electric company will install ground rods for their own systems. Many times these are not full 8 foot rods as is required for your electric service. But technically these are not installed properly as the NEC requires that various grounding electrodes (rods) used for the same building but for different purposes must be bonded together and very often they are not. Electrically it probably doesn't matter at the voltages in use but I'm just sharing information.


How many rods are in a chain?

There are four rods in a chain.

Related questions

How many ground rods are required for a 200amp service in Indianapolis?

According to the NEC, if the ground rod supplements another grounding electrode such as a metal water pipe, you are required 1. If the ground rod or rods is your only grounding electrode, you are required at least 2, at least 6 feet apart. Check with your local jurisdiction for local requirements.


What size is the grounding electrode of a 400 amp service 500CM?

In Canada the grounding electrode requirement is for two steel 5/8" x 10' copper clad rods spaced 10 feet apart.


Should one or two electrical service ground rods be used on a service distribution?

In Canada the requirement for grounding purposes calls for two 5/8" x 10' ground rods placed 10' apart. If rocky ground is encountered, then a grounding plate can be installed. The grounding plate dimensions are 10" wide x 16" long x 1/4" thick. They are galvanized coated and must be buried 24 inched below grade.


How do lighting rods proctect structures?

By grounding electrical energy.


Do copper pipes need to be grounded?

No, the ground wire (green) can be strapped to any metal pipe going to ground. In the absence of a suitable pipe a metal stake at least 6 feet long can be driven into soil and the wire strapped to that.


What do grounding rods do?

If allowed by local codes and regulations, grounding or earthing rods may be used for making safety protective grounding connections to any type of equipment including machinery, household appliances, metal pipework, etc.Whenever and wherever they are needed, grounding or earthing rods must be installed by driving them firmly and deeply into suitably prepared soil within the ground at the earthing point.However nowadays the latest National Electrical Codes and Wiring Regulations in most developed countries insist on using a system of safety grounding wires which are not connected to separate grounding rods installed for each piece of equipment. In that system the safety grounding wires must all be run back to the main circuit breaker panel because it is the main circuit breaker panel which is now the sole point of connection to the main safety earthing point for the whole building or site.Nowadays the main safety earthing point itself may or may not be an actual grounding rod driven into the ground because many codes and regulations now insist that the main safety grounding or earthing point must be made by a well-made connection to the grounded/earthed protective safety sheath of the electricity utility company's service cable coming onto the property, i.e. the site, home or other building. What is required depends entirely on the electrical codes and/or wiring regulations of each particular country.That system provides a better and safer way of providing protective grounding connections for equipment including machinery, appliances, metal pipework, etc.


Minimum length of a grounding electrode?

A standard ground rod is 5/8 x 10'. The amount of rods needed is governed by the electrical code. The largest type of grounding system is a Ufer ground. This is where the bare grounding conductor is embedded in the footings of the building and the weight of the building presses the ground wire to the earths surface. These types of grounds are used mostly in construction and are requested by electrical engineers.


How many ground rods needed for a temporary service at construction site?

The NEC makes no provision for using 1 ground rod even on a temporary service. According to the NEC you must use 2 ground rods. However in my area we are allowed by the local inspector to use just 1. Call your local inspector and see what he requires as he has the last word on this.


How many ground rods are needed for a 100 amp service?

If you're asking this, you shouldn't be installing an electrical service. --- This type of question usually means you aren't ready to do this yourself. Study some electrical material and the National Electrical Code and work this answer out for yourself, or call a professional electrician. If I were to give you an answer, you might attempt to do something you shouldn't be doing, and that may cost someone a shock, a home fire, or their life.


How do you solve a floating earth problem?

Improve the grounding medium with more ground rods or plates and then ground the equipment to the improved grounds.


How to ground and bond a panel?

It must be grounded outside with two 8' copper ground rids driven fully into the ground. One under the meter and one 6' to either side connected together with the proper size copper ground wire. The above answer leaves out the requirement for a grounding connection to a metal water pipe. The NEC actually makes the ground rods supplemental to the water pipe. We don't usually consider the water pipe as the primary grounding electrode but that is how it is treated in the code. Depending on the size of your service, the grounding electrode conductor to the water pipe may actually be a different size than what connects to the ground rods, which are allowed to be connected with 6 AWG copper regardless of the size of service.


What is rod earthing?

It is the installation of ground rods at a service entrance distribution to bring the relative resistance to ground to be within 5 ohms of the utility's distribution network. This grounding system is then connected to the service distribution with a calculated size wire and connected to the distribution at a point within the distribution panel, where the service neutral wire joins the neutral bus bar.