5000000 m 500000000 cm 5000000000 mm 5000000000000 micrometer 5000000000000000 nm 3106.856 mi 5468066 yards 1640400 ft 19685000 in
60 ft lbs is a little more than 80 newton meters it is 81.33 nm
1 nm is 6000 ft, 1 statute mile is 5280 ft and 1.6 km. 1.6 x (6000/5280) = 1.8181km
5 ft 5 in. or 5.42 ft.
(42 in)(1 ft/12 in) = 3.5 ft
14 lbf ft or 19 Nm
Newton meters (Nm) multiplied by 0.738 = Pounds-force feet (lbf ft; lb ft). Pounds-force feet multiplied by 1.356 = Newton meters.
Front axle = 55 lbf-ft. Pinch bolts = 9 lbf-ft. Rear axle = 80 lbf-ft.
This applies to all 1993 to 2002 Mazda 626's: FS & FS-DE ENGINE 2.0L ATX Drive Plate = 71-75 ft-lbf 2.0L MTX Flywheel = 71-75 ft-lbf 2.0L MTX Clutch Cover = 14-19 ft-lbf KL-DE & KL-G4 ENGINE 2.5L ATX Drive Plate = 45-49 ft-lbf 2.5L MTX Flywheel = 45-49 ft-lbf 2.5L MTX Clutch Cover = 14-19 ft-lbf :)
Haynes Manual states that for focus builds between 2001 and 2004 the recommended torque spec for the oil drain plug is 37 Nm / 27 lbf ft.
It is 46 lbf-ft.
You can not convert. Hertz is the frequency in an electrical AC system. lbf is what. If it is suppose to represent ft/lbs there is still no conversion between the two values.
Um... there are 1 psi (lb/in2) = 144 psf (lbf/ft2) , if by (lb ft) you meant pounnds per square foot. then there is 1/144 psi in 1 (lbf/ft2)
A kiloPascal is a measure of pressure, not power or work. It has 1 kPa = 1000 N/m^2 while 1 Watt = 1J/s = 1 Nm/s. Work must be measured in units of force*distance, like Nm or ft lbf. Also Watts measure power which is work/time. As a result, it is not possible to convert Kpa to Watt.
300 ft-lbf at 3200RPM
1 nm is 1 Newton.meter, which is 1 Joule. This equals 0.7376 ft.lbf
Use the following sequence in order to tighten the cylinder head:Tighten bolt 1 to 63 Nm (46 ft. lbs.).Tighten bolt 2 to 58 Nm (43 ft. lbs.).Tighten bolt 3 to 58 Nm (43 ft. lbs.).Tighten bolt 4 to 63 Nm (46 ft. lbs.).Tighten bolt 5 to 63 Nm (46 ft. lbs.).Tighten bolt 6 to 58 Nm (43 ft. lbs.).Tighten bolt 7 to 58 Nm (43 ft. lbs.).Tighten bolt 8 to 63 Nm (46 ft. lbs.).Tighten bolt 9 to 63 Nm (46 ft. lbs.).Tighten bolt 10 to 58 Nm (43 ft. lbs.).Use J36660-A to tighten all the cylinder head bolts an additional 90 degrees in sequence