0
That would depend on how many drainage fixture units you want to drain and which LOCAL code your using.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How much does a 6 foot long 2 inch radius PVC pipe hold?
Approx 904.8 cubic inches.
What are reducer bushings for PVC Pipes?
A fitting that makes it possible, for example, to glue a piece of 2" pipe into a 3" fitting (if you have a 3" x 2" bushing, that is).
How much does 2 x 2 square pipe weight?
In what material ?
What should you slope 2 PVC pipe for a sump pump line?
If the line is outside, sloping will prevent the risk of freezing/braking if there is not water in the line! Inside, it just prevents risk of drips and bacteria growing in what could be stagnant water.
How do you compare the volumes of 6 inch pipe with 4 in pipe?
By calculating the areas of circles with diameters 6 and 4 and comparing those: pi3^2=pi9 pi2^2=pi4 pi9/pi4=9/4=2.25 So the 6 inch pipe holds 2.25 times as much as the 4 inch pipe.
Max waterflow in 2 inch PVC pipe?
What schedule pipe?
How much does 8 inch PVC pipe cost per foot?
about 10$ per foot ANS 2 You're going to the wrong store if you pay that much. I regularly buy it in Canada for 2.85 per foot.
How much does a 6 foot long 2 inch radius PVC pipe hold?
Approx 904.8 cubic inches.
How do you transform a 1.5 inch PVC pipe to a 2 inch pipe?
Put an adapter between them. You can't transform it, you can replace it or change it at some point to 2 inch and continue with 2 inch.
Can you cut into cast iron soil pipe with plastic soil pipe?
You can put up to a 2 inch pipe into a 4 inch. If you are putting 4 inch to 4 inch, either take out a section of the cast and put the PVC in or cut out a section and connect the PVC to the cast with rubber sleeves meant for this. You can use a saddle clamp for the 2 inch. It is a half round piece of PVC with a 2 inch connection in it. It is held on with two U bolts that go around the cast pipe. Put it where you need it and mark the 2 inch hole on the cast. Drill a series of 1/8 inch holes around this circle. when you get them all drilled, you can break out the plug. Try to keep it from falling into the cast pipe. Put the saddle clamp on and connect the PVC pipe as needed. Seal the saddle clamp to the cast pipe with plumbers putty.
How do you boil water in a two inch PVC pipe tested at two-hundred-eighty pounds per square inch at seventy-eight degrees Fahrenheit?
How to Boil Water in PVC Pipe I have been building wood steaming boilers, not PVC steam boxes, for about 2-1/2 years now and using PVC to boil the water in and produce steam. I use sch. 40 PVC and the correct cleaner and cement to go with it. PVC is rated at a much lower than it will really handle. I have run this steaming system for more that 12 hours at a time without any problems and complete safety. If you want more info about this, contact: woodsteamingsystems@yahoo.com. Ernie
How many cubic feet of sand will it take to fill 8'' PVC pipe 2 feet long?
0.7 ft3
How much does water weigh in 3 PVC pipe?
No more than 92 tons DEPENDING on the density of the water. Colder water weighs more. After 90 Tons of weight, care has to be taken with supports. A Better Question would have been How much water /weight would a 3" PVC SCHEDULE 40 pipe 2 ft long hold / weigh SO I am guessing your asking about a mile and a half long 3" pipe SCHEDULE 80
How do you change PVC valve on 2003 Ford Taurus?
The PVC on a 2003 Ford Taurus 6cyl. Duratec engine. I made a tool out of a 3/4 inch PVC plastic pipe i got from Home Depot. I took the new PVC car part and matched it up with the end of the square plastic part by filing out the corners of the pipe and fitting it over the end of the sguare part of the PVC car part. I did this to be able to reach the old PVC so it could be turned 1/2 to the left to get the old PVC car part out.
Why PVC pipes are used nowadays instead of iron pipes?
There are different types of pipes for different types of applications. Every situation has a set of the specific needs to be addressed for that project and the type of pipe to be used. I prefer to use a PVC pipe underground for a water main for the following reasons in California. 1- PVC pipe resists corrosion from the soil it is placed in and will not rust or deteriorate. 2-PVC pipe is much less expensive than copper pipe to install and i can save homeowners money on material costs. 3-PVC resists scale and hard water build up a little better than metal pipe. 4- PVC pipe is easier to install and can bend without the use of fittings for subtle turns or angles. 5-The water will not wear or weaken the PVC pipe. Copper although slowly will weaken with the chlorine and other chemicals found in our water. 6-PVC is not effected by electrolysis unlike copper.
How do you connect PVC to brass?
Yes and NO depending on what kind of piping system. for drain connections yes like tub drains or fixture traps but you need access to all slip/compression fittings. and NO you can not use PVC to brass for like a discharge pipe on a waterheater PRV (pressure relief valve) or any hot water piping system
What is the width of a standard water line PVC pipe?
water line? half inch or three quarters
