0
What else can I help you with?
How many amps on 3 phase 225 amp panelboard each phase?
In a three-phase 225 amp panelboard, each phase will carry 225 amps. This means that the total current flowing through the panelboard is distributed evenly across the three phases, allowing for a maximum of 225 amps on each phase at a time.
If two electrical loads are connected in parallel with each other and each load draws 6 amps what is the total current of the circuit?
The total current in the circuit would be 12 amps. When electrical loads are connected in parallel, the currents add up. So if each load draws 6 amps, the total current would be the sum of both loads, which is 6 + 6 = 12 amps.
If two eletrical loads are connected in parallel with each other and each load draw 6 ampswhat is the total current of the circuit?
When two electrical loads are connected in parallel, the total current in the circuit is the sum of the currents drawn by each load. In this case, if each load draws 6 amps, the total current would be 6 amps + 6 amps, resulting in a total current of 12 amps.
A 220 volt motor is rated at 4.0 amps is that 4.0 amps per leg or 2.0 amps per each leg?
The Full Load Amps, FLA is a rating for each winding of the motor. In this case the motor actually needs 4 amps running through it. As current needs to go somewhere (perferably not to ground) the 4 amps will circulate on you 2 Hots, the neutral isn't needed. 4A in, 4A out.
What is the formula to convert amps to volts?
Amps and volts are two separate parts of power measurement and do not convert into each other. Multiplying amps times volts will give you the measurement of wattage.
What does a cube and a square pyramid have in common?
They are polyhedra, each with a square base.They are polyhedra, each with a square base.They are polyhedra, each with a square base.They are polyhedra, each with a square base.
In a residential 200amp service is 100 amps the maximum that each of the two phase conductor can transmit or can they both carry 200 amps?
Each hot leg to the neutral wire of the service has the ampacity of 200 amps, that is why 3/0 wire is required. A 3/0 copper wire with an insulation factor of 90 degrees C is rated at 210 amps.
Can you run 3 appliances 10-15 amps each through an extension cord with multiplug that is rated for 20 amps?
Not simultaneously because the total current must not exceed 20 amps.
How many chains down one side of a ten acre square?
Each side of a square with an area of 10 acres measures: 10 chains in length.
How many amps are available in a three phase 225 amp panel?
In a three phase 225 amp panel, there would be a total of 225 amps available for each phase, making it a total of 675 amps for all three phases combined. This means that you could have up to 225 amps of current flowing through each phase simultaneously.
What is monoblockamplifier?
Monoblock amps are two separate power amps, one for each channel.They are housed in separate cases. " Dual-mono" power amps are separate power amps-each with its own transformer, but in a single case. Both types are fed by a stereo pre- amplifier.Most amplifiers on the market have only one transfomer supplying both channels.Monoblocks are at the high end.
Are there 100A available on both bars of a 100A panel in a home and for instance can you draw 75A on each bar?
The amp rating of a panel is based on the size of materials used (the bars, etc). You can pull 400 amps through your panel (provided a 400amp breaker was in place); but it would probably melt down very quickly. Basically you have 100 amps total to play with: be it from two 50amp breakers or 30 subpanels pulling 3 amps. :D You just can't pull more than 100amps at one time or the main will trip. The 100 amps is a rating for each bar. If your panel has a 100 amp double pole breaker, then you can use up to 100 amps on each pole. You really shouldn't draw more than 80 amps continuously. But you can count on having that 160 amps avilable if all your loads use only one hot leg of the panel (120 volt loads instead of 240).
