0
If a dimension is 6.804 plus - .005 what is the largest you can go tolerance?
Wiki User
∙ 6y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is 3d plus d?
If your talking maths then its 4 d if your talking viewing on a a screen 3d is 3 dimension and d is dimension
What happens to the perimeter of a rectangle when you double one of its dimensions?
The perimeter of a rectangle is given by (2L plus 2W). If you double either the width or length dimension, then it is four times the original dimension, such as (4L plus 2W) or (2L plus 4W).
Calcuate the quantity of x and it's maximum error if x equals 6a plus 4b where a equals 40 tolerance is plus or minus 2 and b equals 20 plus or minus 2?
320 tolerance +/- 20 ? Did I get it right?
How do you find the dimension of the subspace of R4 consisting of the vectors a plus 2b plus c b-2c 2a plus 2b plus c 3a plus 5b plus c?
The dimension of a space is defined as the number of vectors in its basis. Assuming your vectors are 1,2,1,0 0,1,-2,0 2,2,1,0 and 3,5,1,0 (extra zeros because you are in R4) then you must first check to see if they are linearly indepent. If all the vectors are linearly independent then the subspace defined by those vectors has a dimension 4, as there are 4 vectors in the basis.
When the tolerance limit is less than plus 01 -01 how many decimal places should be used?
1
How can you tell the difference between a general and specific tolerance on a drawing?
IDK that is why i askedGeneral tolerance refers to all untoleranced dimensions, and should be covered by a note on the drawing, eg tolerance unless noted otherwise plus or minus 0.25 mmSpecific tolerance will be included with the individual dimension, either as dimension limits or dimension plus tolerance.
Difference between bilateral and unilateral tolerance?
Unilateral Tolerance :- A tolerancing method using a deviation in only one direction, either plus or minus, from the specified dimension Bilateral Tolerance :- A tolerance method using an equal plus and minus deviation from the specified dimension.
What does tolerance mean with respect to an electrical component?
A tolerance of 10% means that the component's "size" will be within plus or minus 10% of its stated "size". A tolerance of 1% means that the component's "size" will be within plus or minus 1%
What differences are between tolerances of size and tolerances of position?
Tolerance in size is the allowable amount of change in dimension. For example, you want to fabricate a shaft that is 2 cm in diameter plus or minus 2 millimeters. The 2 millimeters is the tolerance. Tolerance in position is the allowable amount of change in position. For example, you need to drill a hole in a wall and you drew a point in the place you want to drill, you are allowed to move as far as 2 millimeters from that hole to receive satisfactory results, this is a tolerance of 2 millimeters in position
What is 3d plus d?
If your talking maths then its 4 d if your talking viewing on a a screen 3d is 3 dimension and d is dimension
What happens to the perimeter of a rectangle when you double one of its dimensions?
The perimeter of a rectangle is given by (2L plus 2W). If you double either the width or length dimension, then it is four times the original dimension, such as (4L plus 2W) or (2L plus 4W).
What is the area of a square with the dimension of 1 plus sqrt3?
4 + 2sqrt3
Calcuate the quantity of x and it's maximum error if x equals 6a plus 4b where a equals 40 tolerance is plus or minus 2 and b equals 20 plus or minus 2?
320 tolerance +/- 20 ? Did I get it right?
What is dimension of 5 aside pitch plus goal mouths?
1 inch
What is bilateral tolerance for 15 plus 000 minus 0.005?
14.9975±0.0025
How do you spell largest in french?
the largest is 'le plus grand / la plus grande' in French.
How do you find the dimension of the subspace of R4 consisting of the vectors a plus 2b plus c b-2c 2a plus 2b plus c 3a plus 5b plus c?
The dimension of a space is defined as the number of vectors in its basis. Assuming your vectors are 1,2,1,0 0,1,-2,0 2,2,1,0 and 3,5,1,0 (extra zeros because you are in R4) then you must first check to see if they are linearly indepent. If all the vectors are linearly independent then the subspace defined by those vectors has a dimension 4, as there are 4 vectors in the basis.
