0
Is the 76 el camino th350 tranny the same shaft length as a 79 Malibu th350?
Wiki User
∙ 18y ago
the th 350 was made with 3 lengths, 6 inch, 9 inch, and 12 inch(12 inch station wagon only)
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
What is the formula for calculating weight using a mild steel cylinder?
gear with shaft dia40mm length 230 teeth 14 shaft dia 25mm width 6.5mm length 168mm
What is the formula for calculating weight of shaft?
Dia X Dia X length X 7.8 / 1000000
What will be the weight of solid shaft dia 760mm and length 1meter?
The weight will depend on the material it is made of, and can be calculated if you know the density of that material. Without this additional information, this question cannot be answered.
Are thrust loads at a right angle to a shaft?
On a ships propeller shaft, the thrust will be in line with the axis of the shaft.
What is an angle shaft?
An angle shaft is an enriched angle bead, with a capital, base, or both.
What type of automatic transmission does a78or79 El Camino use short shaft or long shaft in a 305or350?
It should be the short shaft tranny, I believe the longshaft was used in pick-ups and vans.
Does a 1971 el camino use a short shaft or long shaft automatic transmission?
short shaft
What does the intermediate shaft do?
The intermediate shaft is the shaft going to the driver side wheel from the tranny. The shaft is suppose to eliminate what you call torque steer, It comes straight from the tranny and bolts to the engine block with a bearing race to hold the shaft and at that brace is where the half shaft, or drive shaft connects to the intermediate shaft and to the driver side hub.
What dos the shaft do?
The intermediate shaft is the shaft going to the driver side wheel from the tranny. The shaft is suppose to eliminate what you call torque steer, It comes straight from the tranny and bolts to the engine block with a bearing race to hold the shaft and at that brace is where the half shaft, or drive shaft connects to the intermediate shaft and to the driver side hub.
What are Symptoms of an input shaft leak?
If you mean dripping out of the of the tranny where the shaft slips in then the leaking is it
Where is the Crank Sensor in a 2001 Malibu?
The crank sensor on a 2001 Malibu is located on the bottom of the engine near the crank shaft. It monitors the rotation and speed of the crank shaft.
Why would the th350 tranny in a 1983 el camino 305 make a clinging noise when you shift it into gear?
Most likely, it's the noise resonating along the driveshaft from slop in the rear end gear, u-joints or trans output shaft.
Does a 1971 Malibu have a long or short shaft trans?
short
Where is the crank shaft sensor located on a 2010 Chevy Malibu?
2010 chevy malibu intake position sensor
How do you change the harmonic balancer on 2000 Malibu 3.1?
what do you need to take off car to get to c/shaft pulley on 2001 malibu
Is it easier to change a clutch in a 1989 4 4 truck by dropping the tranny or removing the motor?
Drop the tranny. I replaced a clutch on an '89 Ford 4*4. There is a lot less to undo & do-up on a tranny. Just get some help & a few jacks, drop the drive shaft, and then drop the tranny. Line up your new clutch and use 3 or 4 jacks to raise your tranny evenly twist the shaft till she lines up, give her a shove and bang, put your tranny bolts in, drive shaft, you're on the road or mud. FYI, it will take about a day. ~Shade tree
Will a manual transmission from a 1980 el Camino fit a 1980 Pontiac firebird?
Does your Firebird have a Chevy or Pontiac motor in it?If it is a Pontiac motor, you will need an adapter from Summit or Jeg's.Also, it could be a different output shaft length and spline count.
