0
What else can I help you with?
What is the formula for calculating weight using a mild steel cylinder?
gear with shaft dia40mm length 230 teeth 14 shaft dia 25mm width 6.5mm length 168mm
How to calculate shaft taper?
To calculate shaft taper, measure the diameter at two points along the length of the shaft. Subtract the smaller diameter from the larger diameter to find the taper amount. Then, divide this difference by the length of the taper section to determine the taper per unit length. This result is often expressed as a ratio or in degrees, depending on the application.
What is standard length of 3 wood shaft?
The standard length of a 3-wood shaft typically ranges from 42 to 43 inches for men and about 41 to 42 inches for women. However, individual preferences and specific club designs can result in slight variations. It's important to note that some players may customize the shaft length to better suit their swing and playing style.
Which would provide a greater mechanical advantage -a screwdriver with a 5cm handle and a 1cm shaft or a screwdriver with a 3cm handle and 1cm shaft?
The mechanical advantage of a screwdriver is determined by the ratio of the length of the handle to the length of the shaft. For the 5 cm handle and 1 cm shaft, the mechanical advantage is 5:1, while the 3 cm handle with a 1 cm shaft has a mechanical advantage of 3:1. Therefore, the screwdriver with the 5 cm handle provides a greater mechanical advantage.
What is the formula for calculating weight of shaft?
Dia X Dia X length X 7.8 / 1000000
What type of automatic transmission does a78or79 El Camino use short shaft or long shaft in a 305or350?
It should be the short shaft tranny, I believe the longshaft was used in pick-ups and vans.
Does a 1971 el camino use a short shaft or long shaft automatic transmission?
short shaft
What does the intermediate shaft do?
The intermediate shaft is the shaft going to the driver side wheel from the tranny. The shaft is suppose to eliminate what you call torque steer, It comes straight from the tranny and bolts to the engine block with a bearing race to hold the shaft and at that brace is where the half shaft, or drive shaft connects to the intermediate shaft and to the driver side hub.
What dos the shaft do?
The intermediate shaft is the shaft going to the driver side wheel from the tranny. The shaft is suppose to eliminate what you call torque steer, It comes straight from the tranny and bolts to the engine block with a bearing race to hold the shaft and at that brace is where the half shaft, or drive shaft connects to the intermediate shaft and to the driver side hub.
What are Symptoms of an input shaft leak?
If you mean dripping out of the of the tranny where the shaft slips in then the leaking is it
Where is the Crank Sensor in a 2001 Malibu?
The crank sensor on a 2001 Malibu is located on the bottom of the engine near the crank shaft. It monitors the rotation and speed of the crank shaft.
Why would the th350 tranny in a 1983 el camino 305 make a clinging noise when you shift it into gear?
Most likely, it's the noise resonating along the driveshaft from slop in the rear end gear, u-joints or trans output shaft.
Does a 1971 Malibu have a long or short shaft trans?
short
Where is the crank shaft sensor located on a 2010 Chevy Malibu?
2010 chevy malibu intake position sensor
How do you change the harmonic balancer on 2000 Malibu 3.1?
what do you need to take off car to get to c/shaft pulley on 2001 malibu
Is it easier to change a clutch in a 1989 4 4 truck by dropping the tranny or removing the motor?
Drop the tranny. I replaced a clutch on an '89 Ford 4*4. There is a lot less to undo & do-up on a tranny. Just get some help & a few jacks, drop the drive shaft, and then drop the tranny. Line up your new clutch and use 3 or 4 jacks to raise your tranny evenly twist the shaft till she lines up, give her a shove and bang, put your tranny bolts in, drive shaft, you're on the road or mud. FYI, it will take about a day. ~Shade tree
Will a manual transmission from a 1980 el Camino fit a 1980 Pontiac firebird?
Does your Firebird have a Chevy or Pontiac motor in it?If it is a Pontiac motor, you will need an adapter from Summit or Jeg's.Also, it could be a different output shaft length and spline count.
