0
One hot one neutral one ground. Ground gos to the green screw on the juntion box or plug outlet. hot equals breaker neutral equals neutral bar. Where do you connect the bare wire in a breaker box?
Wiki User
∙ 14y ago
The ground wire goes to the green screw on the junction box first and then to the green screw on the receptacle. When stripping the loom off of the cable leave enough length so that the ground wire does not have to be broken. Make it continuous, so that it can loop around the box ground screw and have enough length, about 4 inches, to end its termination on the receptacle. The other part of the question, the bare ground wire at the panel end terminates on a small bar that is attached to the panel's metal enclosure. It should be mounted on the back inside portion of the "can" just by the side knockout holes.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized
IF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you wire a 220v connection into the main panel?
I assume you mean you are wiring a 220 volt circuit. You will install a 220 volt double pole breaker of the correct size for the circuit. An example would be for an electric dryer that requires a 30 amp double pole breaker wired with 10/3 wire. You connect the Red & Black wires to the breaker. One on each screw. You now connect the White wire to the neutral bus bar in the service panel. Then connect the bare copper ground wire to the ground bus bar in the service panel. At the dryer outlet connect the black & red to the hot screws, white to the neutral, and ground to ground. They will be labeled on the back of the outlet.
If live is kept open could it trip circuit breaker by connecting neutral to ground?
I would think not. However, if live were to come into contact with either the ground, or the neutral or both, this would cause a breaker to trip.
How do you put on a four prong outlet on a roper electric dryer?
Black & Red are hot, and White is neutral. If it has no place to connect neutral connect neutral to ground.
Is it OK illegal or dangerous to connect the neutral to ground to make the circuit work?
If you have to connect the neutral to ground to make the circuit work then you have an open neutral in your circuit. Be careful in handling the neutral as there can be voltage potential on the neutral if a load is connected. In a properly wired home that has been inspected by the local electrical inspector the neutral should be bonded to the ground at the main service distribution point. There will be a green screw that projects through the neutral bus and is threaded into the back of the electrical panel. This should be the one and only place in the whole electrical system where this neutral to ground connection takes place. Dangerous!!!!! The ground is the safety to prevent you from getting shocked due to a malfunctioning piece of equipment. By using the ground for a neutral you will be energizing the entire ground system of you house or business. Thus anything with metal on it and a ground wire going to it will be electrified if the ground fails at the breaker box or building ground rod. Do you want to take this risk? Not I..........
Why are the GFCI breakers nuisance tripping in your 100 amp sub panel- is it because neutral bonded to ground?
It may be the GFCI breaker is defective. Make sure it is wired correctly. Neutral to neutral bar and ground to ground bar.
How do you wire a wire to a wire?
If you are connecting 120 volts, you connect the black wire to the breaker, white wire to the neutral bar, and ground wire to the ground bar. If you are connecting 240 volts connect the black & white wires to the breaker, & ground wire to the ground bar.
How do you wire a 220v connection into the main panel?
I assume you mean you are wiring a 220 volt circuit. You will install a 220 volt double pole breaker of the correct size for the circuit. An example would be for an electric dryer that requires a 30 amp double pole breaker wired with 10/3 wire. You connect the Red & Black wires to the breaker. One on each screw. You now connect the White wire to the neutral bus bar in the service panel. Then connect the bare copper ground wire to the ground bus bar in the service panel. At the dryer outlet connect the black & red to the hot screws, white to the neutral, and ground to ground. They will be labeled on the back of the outlet.
How do you connect wire to a breaker?
There is 220 volts between the two poles. If you are running 2 wires (black and white) + ground then you hook black to one pole and white to the other. Put red or black electric tape on each end of the white wire and wrap around wire for 3 inches or so next to the connection so the next person will be able to see that the wire is hot and not a neutral.
If live is kept open could it trip circuit breaker by connecting neutral to ground?
I would think not. However, if live were to come into contact with either the ground, or the neutral or both, this would cause a breaker to trip.
How is a 208 volt 3 phase electrical sub-panel wired?
Mark the phases red (phase) black (phase) and blue (phase) along with a white (neutral) and a ground (wire size depends on the main breaker amperage) the phases attach to the main breaker unless it is a breakerless panel attach the phases to the lugs on the bus bars top or bottom then connect the neutral to the neutral bus and the ground to the panel
How do you put on a four prong outlet on a roper electric dryer?
Black & Red are hot, and White is neutral. If it has no place to connect neutral connect neutral to ground.
Is it OK illegal or dangerous to connect the neutral to ground to make the circuit work?
If you have to connect the neutral to ground to make the circuit work then you have an open neutral in your circuit. Be careful in handling the neutral as there can be voltage potential on the neutral if a load is connected. In a properly wired home that has been inspected by the local electrical inspector the neutral should be bonded to the ground at the main service distribution point. There will be a green screw that projects through the neutral bus and is threaded into the back of the electrical panel. This should be the one and only place in the whole electrical system where this neutral to ground connection takes place. Dangerous!!!!! The ground is the safety to prevent you from getting shocked due to a malfunctioning piece of equipment. By using the ground for a neutral you will be energizing the entire ground system of you house or business. Thus anything with metal on it and a ground wire going to it will be electrified if the ground fails at the breaker box or building ground rod. Do you want to take this risk? Not I..........
How do you hook up the distribution panel box with red white black and ground wires?
Without more information that appears to be a 240 volt circuit. Red & black would connect to the 240 volt breaker, white connects to the neutral bar, and ground conductor from the ground rods or ground plate connects to the neutral bar. Make sure that the bonding screw is in the neutral bar and it is screwed through to bond the distribution panel enclosure to the neutral bar.
How do you wire a 15 amp breaker?
Ground wire connects to the ground bar, white wire connects to the neutral bar, and black wire connects to the breaker. Be sure and turn off main breaker before installing the wire or the breaker.
How do I rewire an ungrounded plug?
If there is no ground wire connect the ground wire to the neutral wire.
Why are the GFCI breakers nuisance tripping in your 100 amp sub panel- is it because neutral bonded to ground?
It may be the GFCI breaker is defective. Make sure it is wired correctly. Neutral to neutral bar and ground to ground bar.
Where do you connect the speaker ground wire?
remember the + side of the speaker basically means neutral, in all electric projects the - is always the live line, so if + means neutral that basically means that ground would also be neutral, speakers dont need ground, so if u wish connect + with neutral on the speaker.
