0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What degrees do you make an angle and bevel cut for crown moulding on an inside corner?
you could build a miter box that holds the moulding at the same angle as it is mounted between the wall and ceiling. Lay the moulding against the front and back of the box and cut across the face at a 45 degree when viewed above straight down. If the moulding is setting as it would be installed it should fit
How cut plexiglass?
To cut plexiglass you should use a handsaw and make sure it is a handsaw that can cut in straight lines. You should also measure out how you much you need and what shape you need.
Can you cut a square in a single straight line and make a pentagon?
Yes by cutting a corner the square will then have 5 sides
How do you divide a square into 3 equal parts differently?
Cut it from the top and straight down, and make 3 equal sized pieces.
What saw do you cut straight lines with?
coping saw
What is stronger a spiral bevel gear or a straight cut bevel gear?
If both gears designed and manufactured correctly, spiralbevel gear is stronger compare to a straight bevel gear. Spiral bevel gear is also quieter. For example, in mineral processing industry, spiral bevel gears are used in rock crashers because of the higher endurance. When the tooth is spiral (helical) it becomes possible to increase the size of the gear tooth without reduction of the contact ratio. The larger tooth is stronger compare to a smaller tooth. The reason why straight bevel gears are still used is because spiral bevel gears are more expensive in design and manufacturing, thanks to use of expensive spiralbevel gear cutting machines from Gleason Works or from Klingelnberg AG. In 1990, it became possible to manufacture spiral bevel gears on universal CNC milling machines, because of the development of special spiralbevel software for 3d CAD gear tooth modeling. Today, thanks to spiralbevel software, both straight and spiral bevel gears are manufactured on CNC milling machines at the same low cost.
State two reasons why a hypoid type rear axle bevel gear would be favoured over straight cut or spiral type bevel gears?
to all you level 3 phase tester... you just been screwed... work it out for ya self u dick rash
What is a bevel gear?
A bevel gear can change the direction of the driven shaft/axle by 90 degrees. If different tooth counts are used, bevel gears can also change the ratio between speed/strength of the turning motion.
What does a Logan mat cutter do?
A Logan mat cutter is an Economical way to cut mats with a professional finishing product. Logan Mat Cutters produce a perfect Bevel cut using a straight edge.
What is the industry term for bevel cut?
In trim carpentry: scarf joint.
What is the width of a cut made by a saw called?
A Kerf.
Why does my car make a grrrr noise when I back it up?
The grrr noise you hear should be more like a whiring, this is because the reverse gear is a straight cut gear, while all the other gears are helical ( 1st ,2nd, 3rd, 4th and 5th) when two straight cut gears meet there is more noise present due to the way the gears connect, as the reverse gear uses several small gears to change a clockwise motion into a anti-clockwise motion.
How do you cut out a perfect hexagon?
Cut a straight line segment. At its end, rotate the paper in the scissors and make another straight cut. From the end of the second line, again rotate the paper and keeping ways from the earlier cuts, make yet another straight cut. Repeat for the fourth and fifth cuts. Then, rotate and cut, but this time finishing somewhere on the first line segment. You will have cut a shape with six straight sides: a hexagon.
What is a helical gear?
A helical is a spur gear with an angle along the face to increase the gear contact ratio. The gear teeth are cut at angles http://www.motioncontrolguide.com/learn/faqs/gearboxes-and-gears/helical-gears/what-is-the-difference-between-a-helical-gearbox-and-a-straight-gear-tooth-gearbox/ hope this helps
What degrees do you make an angle and bevel cut for crown moulding on an inside corner?
you could build a miter box that holds the moulding at the same angle as it is mounted between the wall and ceiling. Lay the moulding against the front and back of the box and cut across the face at a 45 degree when viewed above straight down. If the moulding is setting as it would be installed it should fit
Why do you cut a one-eighth inch bevel on the insulation when assembling a loadbreak elbow?
to ease the instalation of the elbow
Why is the tip of an injection beveled?
Because the bevel helps the needle cut through the skin with minimum trauma.
