answersLogoWhite

0

What else can I help you with?

Related Questions

What is stronger a spiral bevel gear or a straight cut bevel gear?

If both gears designed and manufactured correctly, spiralbevel gear is stronger compare to a straight bevel gear. Spiral bevel gear is also quieter. For example, in mineral processing industry, spiral bevel gears are used in rock crashers because of the higher endurance. When the tooth is spiral (helical) it becomes possible to increase the size of the gear tooth without reduction of the contact ratio. The larger tooth is stronger compare to a smaller tooth. The reason why straight bevel gears are still used is because spiral bevel gears are more expensive in design and manufacturing, thanks to use of expensive spiralbevel gear cutting machines from Gleason Works or from Klingelnberg AG. In 1990, it became possible to manufacture spiral bevel gears on universal CNC milling machines, because of the development of special spiralbevel software for 3d CAD gear tooth modeling. Today, thanks to spiralbevel software, both straight and spiral bevel gears are manufactured on CNC milling machines at the same low cost.


State two reasons why a hypoid type rear axle bevel gear would be favoured over straight cut or spiral type bevel gears?

to all you level 3 phase tester... you just been screwed... work it out for ya self u dick rash


What is a bevel gear?

A bevel gear can change the direction of the driven shaft/axle by 90 degrees. If different tooth counts are used, bevel gears can also change the ratio between speed/strength of the turning motion.


How can I accurately cut a 45-degree bevel on a table saw?

To accurately cut a 45-degree bevel on a table saw, adjust the blade to a 45-degree angle using the saw's bevel adjustment mechanism. Use a miter gauge or a crosscut sled to guide the wood through the cut, ensuring it stays at the correct angle. Make sure to wear appropriate safety gear and practice proper technique to achieve a precise and clean cut.


How can I make a bevel cut with a circular saw?

To make a bevel cut with a circular saw, adjust the saw's base plate to the desired angle, typically by loosening a lever or knob and tilting the plate. Secure the angle in place, then carefully guide the saw along the material while keeping the base plate flat against the surface. Remember to wear safety gear and practice proper technique to ensure a clean and accurate cut.


What is the recommended angle for a 45 degree bevel cut on wood?

The recommended angle for a 45 degree bevel cut on wood is 45 degrees.


How can I achieve a precise jigsaw bevel cut on my woodworking project?

To achieve a precise jigsaw bevel cut on your woodworking project, follow these steps: Use a sharp jigsaw blade with fine teeth. Mark the angle of the bevel cut on your wood. Secure the wood firmly in place. Start the cut slowly and steadily, following the marked line. Use a guide or fence to help maintain a straight cut. Practice good control and patience to ensure accuracy. Sand the edges for a smooth finish.


What is the difference between a miter cut and a bevel cut in woodworking?

In woodworking, a miter cut is made at a specific angle across the width of the wood, while a bevel cut is made at an angle through the thickness of the wood.


What does a Logan mat cutter do?

A Logan mat cutter is an Economical way to cut mats with a professional finishing product. Logan Mat Cutters produce a perfect Bevel cut using a straight edge.


What is the difference between a miter cut and a bevel cut when it comes to woodworking?

A miter cut is made by cutting across the width of the wood at an angle, while a bevel cut is made by cutting through the thickness of the wood at an angle.


What are the differences between a bevel and a miter cut in woodworking?

A bevel cut is an angled cut made along the thickness of the wood, while a miter cut is an angled cut made along the width of the wood. Bevel cuts are typically used for creating angled edges or corners, while miter cuts are used for creating angled joints or corners.


How can I achieve a precise bevel cut using a circular saw?

To achieve a precise bevel cut using a circular saw, you should adjust the saw's bevel angle to the desired measurement, secure the workpiece firmly in place, and make slow, steady cuts following the marked line. It is important to use a sharp blade and practice proper safety precautions while operating the saw.