C5 X 9.0
The 9.0 is the weight per foot. This is typical for most structural steel.
So....
(19.75/12)*9.0 = 14.8125 lbs
90 HRB
HOW TO CALCULATE THE CONSUMPTION OF FILLER METALThe following tables will help you estimate electrode quantity and cost for a variety of joints. The bases for the tabulations are explained below. Should you encounter a variation in conditions or joint preparation that is not shown in the tables, substitute appropriate figures in the W =D formula and calculate it. Electrode requirements have been calculated as follows: 1-LW =D1-L W=Weight of electrodes requiredD=Weight of steel depositedL=Total electrode lossesTo arrive at the weight of steel deposited, it is necessary to calculate first the volume of deposited metal (area of the groove multiplied by the length). Then this volumetric value is converted to weight by the factor 0.283 pounds per cubic inch for steel. Where weld reinforcement is involved, it is added to the requirements for net, unreinforced welds. These figures are based on the efficiency of the process used. On square and "V" groove joints, the figures are based on stick electrode efficiency. For tubular wire results, divide steel deposit weight by .80 and for solid wire divide by .90.SEEFIGURE1Size of filletL(in inches)Steel depositedper linear footof weld (lbs.)Pounds of electrodes requiredper linear foot of weld* (approx.)Stick*TubularSolid1/83/161/45/163/81/25/83/410.0270.0630.1060.1660.2390.4250.6630.9551.698.049.114.193.302.434.7731.2051.7363.087.034.079.133.208.298.531.8291.1942.123.03.07.118.184.265.472.7371.0611.890*Includes scrap end and spatter lossSEEFIGURE2Joint dimensions (in inches)Steel deposited per linear foot of weldPounds of electrodes required per linear foot of weld* (approx.)MTL. THICK TBEAD WIDTH BROOT OPEN GWithout rein- forcement(lbs.)With rein- forcement(lbs.)Without reinforcementWith reinforcement**3/161/45/163/87/161/201/161/163/321/163/32------ 0.0200.0270.0390.0330.0500.0880.1090.1290.1430.1530.170------ 0.040.050.070.060.090.160.200.230.260.270.301/83/161/41/43/87/1601/321/321/161/163/32------ 0.013 0.0200.0400.0530.0800.1190.1320.1990.2180.2610.288------ 0.030.040.070.100.140.210.240.360.390.470.53SEEFIGURE3Joint Dimensions (in inches)Steel deposited per linear foot of weldPounds of electrodes required per linear foot of weld* (approx.)MTL. THICKTBREAD WIDTHBROOT OPENGWithout rein- forcement(lbs.)With rein- forcements**(lbs.)Without rein- forcementWith rein- forcement**1/45/163/81/25/83/410.2070.3110.4140.5580.7020.8471.1381/163/321/81/81/81/81/80.0850.1730.2820.4890.7531.0881.9300.1430.2580.3940.6410.9421.3202.2400.150.310.500.871.351.943.450.250.460.701.151.682.354.00*Includes scrap end and spatter loss. **R=Height of reinforcement.Figure 1 Figure 2
// set up array int[] nums = new int[] {70, 90, 80}; // iterate and search for(int i = 0; i < nums.length; ++i) { if(nums[i] == 90) { System.out.println("Found 90 at index: " + i); } }
True Bar in stainless steel means the manufacture of the bar is rolled on the thickness and the width, attaining a more 90 degree relationship to thickness and width, unlike sheared and edged condition stainless, which is sheared from stainless plate, which offers a rough, usually out of square edge. True bar also may be defined as HRAP (hot rolled annealed and pickled), thus if you see a listing 304/304L HRAP, it is a True Bar, as this is a stainless rolled product.
...90 volts...
Ryan's Hope - 1975 1-90 was released on: USA: 7 November 1975
about 2mm mild steel max
A US gallon of 90 weight oil weighs approximately 6.8 pounds. An Imperial gallon of 90 weight oil weigh approximately 8 pounds.
90 for regular 92 in hd
it is 90
No, proteins do not make up 90 percent of your body weight. Water makes up 90 percent of your body weight.
What is the weight of a 90 blue band mercury
Vee blocks are mainly used to hold round metal rods or pipes for drilling or milling operations. It is made up of rectangular steel with a 90-degree channel rotated 45-degrees from the sides.
you dont need to lose weight if yiour only 90 pounds and it depends, any type of exersize will help.
90 watts X 4 channel output
The maximum speed of a 1975 Fiat 125 4 cyl 90 hp is approximately 90 mph.
You need to weight 90 pounds