0
What causes code 26 in the ecm on a 89 lebaron 2.5 turbo need help badly i am stranded?
Bemul
Info can be found here http://www.allpar.com/fix/80s-codes.html
26 Peak injector circuit voltage has not been reached (need to check computer signals, voltage reg, injectors) (SEE NOTE #4 BELOW)
NOTE #4.During cranking, the computer will test the current through the injector to see whether there's too much resistance in the injector's path. If there is, code 26 is set.
The problem may be cured with tuner cleaner on the connectors.
For TBI engines, the injector's cold resistance should be between 0.9 and 1.2 ohms (specs vary with year). This is a peak-and-hold injector. With the engine idling the peak period should be about 1.2 milliseconds whereas the hold period will vary. If it's lower than this at idle, then the injector's shorted or there's a defect in the injector driver circuit. (Bohdan Bodnar)
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is the timing for a 1989 Chrysler LeBaron turbo?
if it is a 2.5L it should be 12 degrees before t.d.c.
Where is the silencer ring on a 7.3?
A 7.3 powerstroke's stock Garret turbo does not have a silencer ring inside the turbo housing.
Difference between a variable vane turbo and non variable vane turbo?
Vanes inside a turbocharger control the acceleration of gases inside the turbo and thus the speed at which the turbocharger itself can accelerate the compressor and produce boost. Tight vanes produce a quick spooling turbo with little lag but one that can quickly choke the engine at higher speeds. This is because the engine is trying to push to much exhaust through the turbo and the vanes are constricting it. Wider spaced vanes can allow a turbo to have more top end capability but at the expense of spool time (otherwise known as turbo lag). With a variable vane turbo the vanes themselves can be adjusted on the fly allowing the turbo to spool quickly and still be able to produce good efficiency at higher engine speeds. The technology has been about for a few years in diesel engines but has been slow in coming to gasoline engines due to increased exhaust temperatures found in gasoline engines. These increased temperatures cause lower rates of reliability. The technology has been used in gasoline engines most recently in the 2006-2007 Porsche 911.
What is the 0 to 60 of a Renault 5 turbo?
7.1 sec to 60
Duramax turbo lines are blowing off?
wow that is a hard question
Can you bypass the turbo on a 1985 Chrysler LeBaron?
No.
Can a Chrysler lebaron run if the turbo is removed?
Sure
What is the Firing order on a 88 lebaron 2.2 turbo?
1,3,4,2
Where is fuel pump on a 1986 Chrysler LeBaron turbo?
It is inside the fuel tank.
What is the oil capacity for a 88 lebaron 2.2 turbo?
4 quarts of 5W-30
How many liters of gas does a 1986 Chrysler LeBaron turbo GTS hold?
56
89 Lebaron 2.5 non turbo fuel pressure at idle?
14 psi
How to adjust oil presser on LeBaron 2.2 turbo 1991?
you dont. why do you think you need to adjust it?
What is the timing for a 1989 Chrysler LeBaron turbo?
if it is a 2.5L it should be 12 degrees before t.d.c.
How to change the EGR valve on a 1987 LeBaron 22l turbo engine eowawa?
Ther is no egr valve on the 2.2 turbo engines. With FI and turbo, there was no need. Some of the earlier carb engines did have egr.
How much power steering fluid will a LeBaron 2.2L turbo hold?
It will hold between two and three quarts
Does your 89 lebaron have a saginaw or zf steering pump?
My 89 lebaron 2.5 non turbo has the ZF (plastic reservoir) power steering pump.....and I need to find a replacement as the low pressure line has broken off!
