0
What does 5.5 mean in RST 5.5 interrupt of 8085 microprocessor?
Wiki User
∙ 11y ago
The 5.5 in RST 5.5 means that the interrupt vector is located between RST 5 and RST 6.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the lowest priority interrupt in the 8085 microprocessor?
The lowest priority interrupt in the 8085 microprocessor is INTR, unless you also consider the software interrupts, RST 0 through RST 7, which are even lower.
Describe RST 5.5 interrupts in 8085 microprocessor with examples?
RST 5.5 is level triggered interrupt & maskable also. it can be masked by using SIM intrruction. Vector address of the RST 5.5 interrupt is 002Ch
What does 6.5 signify in rst 6.5 of 8085 microprocessor?
The name, RST6.5, was chosen because the interrupt vector lies halfway between RST 6 and RST 7, specifically at address 0034H.
What is the use of RST?
RSTn(0-7) is software interrupt & RST(7.5,6.5,5.5) are INTEL's 8085 maskable interrupts their priority is respectively 7.5,6.5,5.5.RSTn.5 is hardware intterrupt and it is controlled by the external pin available on the chip of 8085. it is used to interrupt the microprocessor from its normal execution and tends to execute some ISR(interrupt service routine)
What does rst in 8085 software interrupt stand for?
RST is simply the opcode chosen to represent the Restart instruction.
What is rst 5.5 in 8085?
RST 5.5 is an interrupt request pin (pin 9) on the 8085. It is sampled, along with other interrupt requests, one clock cycle before ALE on the falling edge of CLK. When enabled, and having priority, it causes an interrupt vector sequence using the RST 5.5 instruction, going to location 002CH.
What is the interrupt number in 8085 microprocessor and how to find interrupt's vector address?
The 8085 has five interrupts, INTR, RST5.5, RST6.5, RST7.5, and TRAP. It also has eight software interrupts, RST0, RST1, ..., RST7. The INTR interrupt requires a hardware response that is an opcode. Usually, the opcode is either a CALL instruction, in which case the interrupt vector can go anywhere in memory, or it is an RST instruction, in which case the vector is based on a table in low memory. In the case of RST instructions, either directly or via INTR, or the RSTx.5 interrupts, you simply multiply the interrupt number by 8 to get the vector address. The following table presents the vector addresses for all possible interrupts... RST 0 - 00H RST 1 - 08H RST 2 - 10H RST 3 - 18H RST 4 - 20H TRAP - 24H RST 5 - 28H RST5.5 - 2CH RST 6 - 30H RST 6.5 - 34H RST 7 - 38H RST 7.5 - 3CH
What is the use of Interrupt vector table of 8086 microprocessor?
The interrupt vector table in the 8085 is a region of low memory that contains the target addresses for the RST instructions. RST can be invoked by the program, by an INTR request which provides an RST x instruction in response to INTA, or by one of the four direct interrupt pins, TRAP, RST5.5, RST6.5, and RST7.5 Each of these interrupt sequences place the PC on the stack, and then execution goes to one of the vectors. The vectors are as follows... RST 0: 0000H RST 1: 0008H RST 2: 0010H RST 3: 0018H RST 4: 0020H TRAP: 0024H RST 5: 0028H RST5.5: 002CH RST 6: 0030H RST6.5: 0034H RST7: 0038H RST7.5: 003CH
What is the function of interrupt acknowledge pin in 8085 micro processor?
The INTA- (Interrupt Acknowledge) pin on the 8085 is an acknowledge of the INTR (Interrupt Request). It has the same timing as RD-, and external hardware is expected to provide an opcode, usually a CALL or an RST instruction, in response to INTA-.
What is SIM and RIM instruction in microprocessor?
RIM stands for read interrupt mask and SIM stands for set interrupt mask.The SIM instruction is used to copy the contents of the accumulator into the interrupt mask.The RIM instruction is used to interpret the RST interrupt positions.
What is RST in 8085?
RST OF TRAP is 24h(hexadecimail) address.
What is the importance of INTA in 8085 microprocessor?
The INTA- pin on the 8085 is a read strobe that is used in response to the INTR sequence. It has the same timing as RD-, and external hardware is expected to provide an instruction opcode and, if necessary, the extra bytes, in response to INTA-.One of the enhancements made in the 8085 over the 8085 is the RST type instructions, which are single byte calls to specific locations in low memory. External hardware can be simplified by providing the RST opcode, without needing to provide a full CALL instruction.Not asked, but answered for completeness - the other four interrupt pins, RST5.5, RST6.5, RST7.5, and TRAP are 8085 enhancements that allow the use of automatic interrupt vectoring without using the INTA- pin.
