0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What type of LAN architecture will coax use?
It could be star or bus, but historically, coax cable was used in bus architecture.
How do you find the ip address?
If you want to find your IP address,visit Ip-details.com .
What does it mean to enable AP mode in net gear wndr3400 router?
This means that the device will no longer be a "router" ... it will simply pass through IP addresses in the same subnet as the one it is given (presumably by an upstream router). This is useful for networks where there is an existing router (e.g., uverse gateway) with built-in wireless, but you want to locate the wireless access point in a different location from the router. Note that a router would typically have an IP address in one subnet (provided by the WAN or an upstream router) and it would provide IP addresses using DHCP typically in another subnet. So your cable modem is a router in that it gets an external IP from the cable company. But then it provides 192.168.x.x addresses to you. If you add an additional router it might be given a 192.168.x.x address and then provide 10.1.1.x addresses to you. If the additional "router" above were in "AP mode" then it would have a 192.168.x.x address and it would pass through DHCP requests to the cable modem... so everybody would get a 192.168.x.x address.
How can you change facebook ip adrress?
Your IP address is th internet connection you have. You can not change your IP unless you get another internet connection.
Class A IP address range?
192.168.0.254 is a valid "class C" IP address.
The bus cable to which computers on the Ethernet is connected?
The bus cable to which computers on the Ethernet is connected is called the trunk. If the trunk breaks, a bus topology is completely disrupted.
What network topology connects to a trunk cable?
Bus Topology.
What describes the external IP address that is obtained by a router through a cable or DSL modem?
What describes the external IP address that is obtained by a router through a cable or DSL modem?
What is the io bus controller?
it is used to control the carry the data on bus cable
What is A cable with terminators at each end and is shared by all nodes?
Bus Cable
What is a cable with terminators at each end and is shared all nodes?
Bus Cable
Advantage of token bus?
less cable
Need for assessing a local area network?
get the ip address and the cable's to connect
What hardware does a bus topology need?
A bus topology needs a trunk cable, which is a high speed central cable to which all the nodes can be connected. If the trunk cable breaks down, however, the whole network comes to a halt.
How you connect laptop with PC?
If you are using a crossover cable, simply assign static IP's to each machine (192.168.0.2 and 192.168.0.3). If using regular network cable, you will need to use a network switch or hub to connect them together, still using the static IP's for each machine.
We are switching to IP phones at work.?
IP phone lines work by transmitting phone signals through the cable lines, rather than through the traditional phone lines. The downside is that the phones are tied directly to the cable, and if one is out so is the other.
Where is the ip address on a cisco switch for telnet?
The Cisco switches I have seen don't have an IP address by default. You have to connect to the switch with a console cable - one that connects to the console port on the switch, and to the serial port on the computer - and do some initial configuration, including the IP address.The Cisco switches I have seen don't have an IP address by default. You have to connect to the switch with a console cable - one that connects to the console port on the switch, and to the serial port on the computer - and do some initial configuration, including the IP address.The Cisco switches I have seen don't have an IP address by default. You have to connect to the switch with a console cable - one that connects to the console port on the switch, and to the serial port on the computer - and do some initial configuration, including the IP address.The Cisco switches I have seen don't have an IP address by default. You have to connect to the switch with a console cable - one that connects to the console port on the switch, and to the serial port on the computer - and do some initial configuration, including the IP address.
