0
A: It is a standard statement to signify that the amplitude is one half.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Why 3dB is required in the frequency graph?
as upto 3db only the amplifier gives the linear output & after that it gives non linear so it is difficult to determine it's characteristics.also up to 3 db it's energy efficiency is 70.3%. ANSWER: It imply that the amplitude on the output is half.....................
How value of c is calculated in an RC filter for a given value of r?
Time constant = R C C = time constant/R R = time constant/C When used as a filter, Cutoff frequency = 1 / (2 pi) R C R = 1 / (2 pi) (cutoff frequency) ( C ) C = 1 / (2 pi) (cutoff frequency) ( R )
What barclays branch has sort code 20-69-40?
Barclays Bank, 62 High Street, Cosham, Portsmouth PO6 3DB
Would a 3db difference between two speakers that handle the same wattage make the one with 3 extra db twice as loud?
no
What is the ratio of a frequency to its total frequency?
The ration of a frequency to its total frequency is called relative frequency.
What do you mean by 3 dB cutoff frequency?
3db frequency is the frequency at which the value in the graph is reduced by 3db level It's also known as the half-power point.
What is cut off region of an amplifier?
Amplifiers react differently to different frequencies. The amount that an amplifier reacts is usually measured in power (decibels). At a certain frequency (usually higher frequencies) the amplifier will react (output) only 50% of the power it is given (this works out to -3dB) this is the standard cutoff frequency and the cutoff region is anywhere below -3dB on a bode plot(This is a plot which shows the frequency input versus the response. These are very common when talking about amplifier characteristics).
What is alpha cut of frequency?
it is the frequency at which the current amplification drops 3dB below its low frequency value.
How does a capacitor acts as a filter?
The cutoff frequency of filter depends upon the value of capacitor and resistance. Therefore, below cutoff frequency or above this frequency, capacitor allow to pass all other frequencies.
How does a capacitor act as a filter?
The cutoff frequency of filter depends upon the value of capacitor and resistance. Therefore, below cutoff frequency or above this frequency, capacitor allow to pass all other frequencies.
What is a -3dB point in an inverting amplifier?
The -3dB point is the point of half power. In a filter, the -3dB point, more commonly called the half-power point, is the point where the output power is one half the input power. A bandpass filter has two half-power points, and the distance between them is called the bandwidth, whereas a low-pass or high-pass filter has one half-power point, which is called the cutoff frequency. In terms of voltage, the half-power point is where the voltage is 0.707 (1 / square root(2)) of the input voltage.
The attenuation in wave guides near the cutoff frequency is?
zero
Why you take cutoff freqency at 3dB?
3 dB implies 1/2 the power and since the power is proportional to the square of voltage, the voltage will be 0,707 of the passband voltage. sqrt(0.5) = 0.707
What is band rate?
ANSWERED MY MUHAMMAD WALEED SHAIKH first of all we have to know that about band,so band is range of frequency which we have selected for example:we have a low pas filter it frequency always started from initial or 0 HZ upto cutoff frequency and here remember that cutoff frequency we will have to select after cutoff signal is rapidly down now about band rate so your signal is band at certain rate is called band rate.
How value of c is calculated in an RC filter for a given value of r?
Time constant = R C C = time constant/R R = time constant/C When used as a filter, Cutoff frequency = 1 / (2 pi) R C R = 1 / (2 pi) (cutoff frequency) ( C ) C = 1 / (2 pi) (cutoff frequency) ( R )
Why 3dB is required in the frequency graph?
as upto 3db only the amplifier gives the linear output & after that it gives non linear so it is difficult to determine it's characteristics.also up to 3 db it's energy efficiency is 70.3%. ANSWER: It imply that the amplitude on the output is half.....................
What is the lowpass filter cutoff frequency that must be used to decimate to reduce the sampling rate from 8kHz to 4kHz?
2kHz - That's the nyquist frequency at a sample frequency of 4kHz.
