0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you work out the flat dimensions of a cup sleeve?
measure the Circumference of both the top and bottom edges of the sleeve. measure the height of the sleeve. using a centerline draw the first Circumference(kinda of like a lower case "T") measure down the height of the sleeve along the centerline, draw in the other Circumference. connect the endpoints on the left then the right. you now have a flat drawing from which to measure your dimensions, area, etc.
What is the difference between a 3d bend and a 3R ell?
There is no difference. Different suppliers and contractor describe the same situation with 3R or 3D. Here is how to think about it. A piping segment is formed or bent at a radius. The radius is measured at the centerline of the bend. The radius of the bend centerline is 3 times the nominal diameter of the piping segment being bent. 3R means the bend radii is three times the nominal pipe diameter. 3D means three times the nominal pipe diameter is the bend radii of the piping segment. Caution don't begin to convert 3R to 1.5D. Not applicable with this terminology. Standard long ells can be purchased with 3R bends, being 10 inch pipe ells have a bend radii of 30 inches.
What are the proper measurements for setting a toilet?
According to the 2006 International Plumbing Code, the following are the minimum dimentions for setting a toilet: From rear wall to center of drain line = 12 1/2 inches min. (General Standard Not Code) From side wall or side cabinet to center of drain or centerline of toilet = 15 inches min. From front of toilet to front wall or cabinet = 21 inches min. From front of toilet to Toilet dispenser = 7 to 9 inches. I hope you find this usefull. Terry
What is the reciprocal of -1?
The reciprocal of 1 is 1. Proof: a. 1*(1/1) = 1 because a*(1/a) = 1 b. 1*1 =1 because 1*a = a c. 1/1 = 1 compare a. and b.
What is 1 equals 1?
It is negative infinity.
How far should a centerline extend from object line?
1/4"
Why do you want the centerline of the runway to be on the drivers right?
The centerline of the runway is in the center, not on the right.
What is camshaft angle that is measured in camshaft degrees?
No, it is in crankshaft degrees, an example: intake centerline of 108* degrees, means the centerline occurs 108 degrees past Top dead center on cylinder 1.
How far is centerline station 2 away from the initial offset of the centerline point?
400 feet
What is Rear track of a car?
Track is the dimension from the centerline of the tire tread on one tire to the centerline of the tire tread on the opposite tire on the same end of the vehicle, front track or rear track. Wheelbase is the dimension from the centerline of the front tire to the centerline of the rear tire.
How far is Centerline Station Number One located from the initial offset centerline point?
200 feet
How do you set the centerline with auto level?
You set the centerline with auto level by making use of the virtual colonoscopy.
What does a double yellow centerline mean while driving?
You're not allowed to pass the car in front of you while theres double yellow centerlines. You can only pass a car if theres a single yellow centerline and strips of a yellow centerline on your side of the road or just a yellow strips centerline.
Define Centerline in Badminton?
The line in the center...
What is the angle of the intake valve on a big block Chevy?
26° relative to bore centerline and then 4° relative to crank centerline. Exhaust is 17° and also 4°.
What is the springline of a pipeline?
Another name for the centerline of the pipe.
How far from the centerline is the on-guard line?
two meters.
