0
What else can I help you with?
What is center line on a boat?
The centerline on a boat refers to an imaginary line that runs longitudinally along the length of the vessel, dividing it into two symmetrical halves. It is crucial for balance and stability, as it helps in determining the boat's alignment and weight distribution. The centerline is often used as a reference point for measurements, navigation, and positioning of equipment. Additionally, many boat designs incorporate features along the centerline to optimize performance and handling.
What is the dimension center to face of a 45 degree 5D elbow?
The dimension from the center to the face of a 45-degree 5D elbow typically refers to the centerline radius of the elbow. For a 5D elbow, the centerline radius is five times the nominal pipe diameter (D). Therefore, the center-to-face dimension for a 45-degree 5D elbow would be calculated as the centerline radius plus half of the diameter of the pipe, which is 5D + (D/2) = 5.5D. This can vary slightly depending on specific manufacturer standards, so it's always best to consult the technical documentation for the specific elbow being used.
How do you work out the flat dimensions of a cup sleeve?
measure the Circumference of both the top and bottom edges of the sleeve. measure the height of the sleeve. using a centerline draw the first Circumference(kinda of like a lower case "T") measure down the height of the sleeve along the centerline, draw in the other Circumference. connect the endpoints on the left then the right. you now have a flat drawing from which to measure your dimensions, area, etc.
What is the formula for a long radius 90?
The formula for a long radius 90-degree elbow in piping is typically described by its radius and angle. The radius (R) is measured from the centerline of the pipe to the centerline of the elbow, with long radius elbows typically having a radius that is 1.5 times the nominal pipe diameter (1.5D). This design minimizes pressure loss and turbulence in fluid flow compared to short radius elbows.
How do you calculate the skew angle on the motor shaft?
To calculate the skew angle on a motor shaft, first measure the distance between the centerline of the motor and the centerline of the shaft at both ends. Then, determine the angular displacement by using trigonometric functions, specifically the tangent function, where the skew angle (θ) can be found using the formula θ = arctan(opposite/adjacent). Ensure to account for any misalignments and verify measurements for accuracy.
Why do you want the centerline of the runway to be on the drivers right?
The centerline of the runway is in the center, not on the right.
How far should a centerline extend from object line?
A centerline typically extends 1/8 inch from an object line on both sides. This standard measurement helps provide clarity and consistency in technical drawings and blueprints.
What is camshaft angle that is measured in camshaft degrees?
No, it is in crankshaft degrees, an example: intake centerline of 108* degrees, means the centerline occurs 108 degrees past Top dead center on cylinder 1.
How far is centerline station 2 away from the initial offset of the centerline point?
400 feet
What is Rear track of a car?
Track is the dimension from the centerline of the tire tread on one tire to the centerline of the tire tread on the opposite tire on the same end of the vehicle, front track or rear track. Wheelbase is the dimension from the centerline of the front tire to the centerline of the rear tire.
How far is Centerline Station Number One located from the initial offset centerline point?
200 feet
How do you set the centerline with auto level?
You set the centerline with auto level by making use of the virtual colonoscopy.
What does a double yellow centerline mean while driving?
You're not allowed to pass the car in front of you while theres double yellow centerlines. You can only pass a car if theres a single yellow centerline and strips of a yellow centerline on your side of the road or just a yellow strips centerline.
Define Centerline in Badminton?
The line in the center...
What is the angle of the intake valve on a big block Chevy?
26° relative to bore centerline and then 4° relative to crank centerline. Exhaust is 17° and also 4°.
What is moving toward the centerline of the body called?
Adduction
How far from the centerline is the on-guard line?
two meters.
