There is no specific distance specified in the code book. The meter stack has to be on the outside of the building and some times this means bringing it through the eave end of the roof line. The connection point has to be 15 feet high as a minimum. The utility meter has to be at head height on the outside wall for the meter reader to see and read it. On the lower end of the meter stack is the electrical panel. As you can see the distances will change in every circumstance depending on where the electrical panel is placed. The electrical panel can not be placed any further in the building from the outside wall than ten feet.
Trailing edge is the rear edge of a wing.
Flip flop is edge triggered device
"What is an antenna": the antenna is a device that couples electromagnetic fields between free space and a circuit (radio, cell phone, etc.).An omni or omni-directional antennais one that works equally well in all directions. Real antennas can only approximate this to a greater or lesser degree. In most applications, but not all, when someone says "omni antenna" they mean it works the same as you go around the antenna in azimuth.The shape of a "typical" simple donut explains this very nicely. Going around the round edge of the donut, it is the same in all directions. But if you go up from the edge to the top of the donut, its shape changes. It's the same with a simple omni antenna. If you have one on your desk as a wireless access point and you walk around the antenna at the same distance, it will work just the same at every point in your walk. If you climbed up a ladder, though, then as you go up the ladder you will be going towards the top of the donut and how the antenna works will change.A panel antenna is made very differently from an omni-directional antenna. It works a bit like a flash light, focusing all the energy in one direction. If you had a flash light sticking out from the front of a panel antenna, you'd see it stick out a lot in the front and only a little to the sides and up/down. Likewise, the panel antenna works mostly straight in front and only a little to the sides and up/down.
flipflop is edge triggering and latch is level triggering
You are absolutely correct.
pop out small panel behind door pull remove two torx screws , remove two pop out connectors on outer edge of door panel near door latch ,grab bottom of door panel and pull it towards you this will release panel ,disconnect wires as needed if you want to remove entire panel from door, lift up on panel to remove it from edge of window track
* Disconnect the negative battery cable * At the bottom of the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors then remove the door panel
* Disconnect the negative battery cable * At the bottom of the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors then remove the door panel
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors
* Disconnect the negative battery cable * At the bottomof the door panel remove the two screws * Pry up at the front edge of the power window switch pod and lift it out then unplug the electrical connector * Remove the inside door handle escutcheon * Remove the screw in the door pull pocket * Pull the door panel away from the door far enough to disconnect the electrical connectors