0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Does it take the same force to pump water vertically to x feet as it does up a slope to the same height?
No. would it take the same amount of energy to pump water 1 foot up and 25 inches over as it would to go 400 miles over and 1 foot up? Unless you are under frictionless conditions, no.
How many syllables in pump?
There is one syllable in pump.
What event initiates ATP attachment to the Na plus -K plus pump leading to the pump's phosphorylation?
The binding of Na+ ions to the pump
How does the fire department use hydraulic multiplication?
The term hydraulic multiplication is usually applied in fire fighting to indicate that water pressure is increased by the use of multiple "stages" to jack up pressure and delivery rates. Let's look at an example. An engine company arrives at a structure fire and the engine commander knows that fighting this with water in the tank will not be a good tactic. He orders a reverse lay (2 x 2 1/2" lines, or perhaps a 4" supply line, depending), and the engine is then set up at the hydrant to act as a manifold. The engineer connects the pump suction to the hydrant. There is pressure in the mains that feed the hydrant, but the pump in the engine will take that pressure and step it up to pump water through the two lines to the "scene" of the fire. The second-in engine sets up at the end of those two lines, and connects one to the suction of itspump. Let's review what is happening as regards the hydraulic multiplication. Pressure in the mains (at the hydrant) is multiplied by the first-in engine and delivered to the second-in engine. The second-in engine multiplies that to deliver water to large (almost certainly 2 1/2") handlines on the fire ground. Any appliance on that second engine is also employed to direct a stream. If a truck arrives (which it should, eventually), it can hook up to the second-in engine, and that engine will then pump to the suction of the truck's pump. That's hydrant outlet to an engine, to another engine, and on to the truck. The truck will deploy its high reach nozzle(s) to get more wet stuff on the red stuff. It's easy to see that the hydrant can only be tapped for so much flow, but the hydraulic multiplication of the three pieces of apparatus here is a no brainer. If water needs to be moved up a long, steep hill, like perhaps in San Francisco, it might not be unusual for several engines to pump that water up the hill. And there might even be a fire boat at the bottom as the first link in the chain. The San Francisco Bay is a virtually unlimited water source!
Is pump a syllable?
No.
What relationship has between concrete pump pressure and concrete slump?
The higher the slump (usaly 100 to 150 slump or S2 to S3) the easyer it is for the pump to pump it. It also needs to be a 'pump mix' that has a height quantity of sand in it to prevent it from separating. Regards Colin
Need a concrete slab 11 x 22 x 5 how do you get it to site without truck access?
You can pump it using a concrete pump truck. You can use a wheel barrow... probably need more than one. Or you can use a Georgia Buggy, a motorized container designed for that purpose.
How much does it cost to pump a yard of concrete?
Be careful usually it takes a yard just to fill the hose on the pumper truck
What is concrete pump?
Concrete Pump is an equipment mounted on a Truck Chasis, which does the job of Mixing the cement Mortar and delivering the same at work site as ready Mix concrete. Since the mortar mix can directly be poured or pumped to cast the slab or column or any other structural component, it is termed as Concrete Pump please visit the URL : - http://www.concretepumps.com for further reference.
How do you put conrete in backyard?
If by conrete you mean concrete, it is put in the backyard the same way as it is put in the front yard. However, in some cases, you cant access the backyard from the street therefore an concrete pump is needed. The concrete truck will empty it's load into a hopper on the back of the concrete pump. Then it gets pumped through a pipe which is held up by a remote controlled boom, allowing concrete to be pumped over fences, houses etc...
How much does a yard of concrete cost in Alabama?
One yard of delivered concrete is $250.00. Prices change according to location. One cubic yard contains 27 cubic feet. Concrete is sold in cubic yards. A yard of concrete weighs approximately 4200 pounds.
Where is the fuel pump in a 1987 Mitsubishi Truck?
where is the fuel pump in a 1987 Mitsubishi Truck
How do you replace water pump on Isuzu truck?
how do I remove the water pump from my 1990 Isuzu truck?
How hard is it to replace fuel pump on 2000chevrolet truck?
how is it to replace fuel pump on 2000 Chevrolet truck
What is the maximum limit of slum for pump concrete?
Required slump for pump concrete is 100 -200 mm is suitable with used of admixture
How concrete pump works?
A concrete pump which comprises an elongated hollow housing in which a valve element reciprocates. The valve element includes a pair of transversely extending tubes and a pair of concrete guiding chambers. The valve element moves between two positions. In the first position a first guide chamber is opposite a first pump cylinder and guides concrete from an upright conduit associated with the first pump cylinder into the first pump cylinder and a first tube is opposite a second pump cylinder and guides concrete from the second pump cylinder into a discharge line associated with the second pump cylinder. At the second position a second guide chamber is opposite the second pump cylinder and guides concrete from an upright conduit associated with the second pump cylinder into the second pump cylinder and the second tube is opposite the first pump cylinder and guides concrete from the first pump cylinder into the discharge line associated with the first pump cylinder.
Where to find a fuel pump fuse on a 1999 gmc truck?
where i the fuse for a fuel pump on 1991 gmc truck
