0
What is the name of the rounded area at the edge of each bearing journal?
Wiki User
∙ 7y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the difference in area between a kite and a rhombus?
The dimensions of each one are going to have some bearing on the answer.
What is the volume of a cube if the surface area is 78in?
Each face of the cube has 1/6 of the area = 78/6 = 13 in2 .Each side of the face = square root of the area = sqrt(13) inches .The volume of the cube is (side length)3 = [ sqrt(13) ]3 = 46.872 in3 (rounded)
How wide is a square acre?
An acre of area can have any shape at all. If it's laid out in a square shape, then each side of the square is 208.71 feet long. (rounded)
What is shape with an area of 10.5 sq cm?
There are an infinite number of them. You can draw any shape at all, and I can shrink it orblow it up so that it has an area of 10.5 sq cm.If it's a square, then each side of it is 3.24 cm long (rounded).If it's a circle, then it has a diameter of 3.656 cm (rounded).If it's a rectangle a mile long, then it's 0.0000652cm wide (rounded).But it can be any shape that you happen to like today.
Is the rounded bony protuberance on each side of the ankle?
condyle a rounded protuberance at the end of some bones
Why use journal bearing in turbine?
putting a journal bearing at each end of the turbine rotor or shaft would be to support it.
How can you measure bearing?
It depends on the type of bearing, and which measurement. A double race roller bearing is measured on the inside (shaft diameter) with an internal vernier caliper or similar device. On the outside (casing or pillow block diameter) with an external vernier. And the width (or length) of each race can be measured with and external vernier. A babbitt bearing can be measured by measuring the journal on which it is to be mounted, then taking "leads" (or using plastigages), by placing lead fuse wire or a plastigage on the journal, placing the bearing top half over the leads, and bolting down the bearing housing over that. Then unbolt the bearing housing remove the top half the bearing and with a micrometer measure the crushed thickness of the fuse wire. Add this to the journal diameter to get the internal diameter of the bearing. The main reason for taking leads is to determine the oil wedge gap in the bearing to see if it is the right thickness. If it is too thin the bearing needs to be scraped if it is too thick the bearing needs to be replaced or the journal built back up to the correct diameter.
What is the difference in area between a kite and a rhombus?
The dimensions of each one are going to have some bearing on the answer.
How do you remove babbitt from crankshaft?
I assume you mean the bearing lining from a stuck or spun bearing. You can have the crank turned at a machine shop, or you can use strips of emery cloth and polish it off. Use strips 12 to 18 inches long and as wide as the journal. Rotate the crank as far as you can to one side, the 8 or 9 o'clock position, put a strip of emery cloth over the journal and holding each end in a hand, polish the crank. Do this for a while and then rotate it to the 3-4 o'clock position and do the same. This should let you get to the entire journal.
Where is the abs wheel sensor on the 2005 Chrysler pacifica?
There is one at each wheel bearing.There is one at each wheel bearing.
How do you tell if the rod bearings are oversized?
The bearing size is stamped into each bearing halve.
How big is 44 square kilometers?
It's the area inside a square that's 4.12 miles on each side (rounded number).
What do the different towns name indicate ?
Each indicates a different example of abuse in Dix’s journal
How do you change a wheel bearing on a roller skate?
you have to buy a bearing pusher tool to get it out i suggest the kryptonics one tool because each bit on it has a bearing pusher
How do you calculate white metal bearing clearances?
There is no simple formula to calculate the metal bearing clearance. Manufacturers must specify the clearance for each individual bearing.
What is the volume of a cube if the cube has an area of 4 square feet?
Total area = 4 square feet.The cube has 6 faces.Area of each face is (4/6) square foot.Area = square of the length of each edge.Length of each edge = square root of the area of each face.Length = sqrt(4/6 square foot) = 0.8165 ft = 9.798 inches (rounded)
If the area of a square is 72 inches squared find the radius?
A square doesn't have a radius. A circle has. If the area of a square is 72 inches2, then each of its sides is 6 sqrt(2) = 8.485 inches. (rounded)
