Best Answer

disconnect ground on battery terminal,locate starter there shoulb be 2 wires n possibly a plug,disconnect plug take nuts off the that hold the wires on then there are 2 bolts that hold starter to transmission take those out and pull starter out compare with new starter if the same put it in put bolts in reconnect wires n plug reconnect ground...your done

User Avatar

Wiki User

โˆ™ 2011-04-13 15:00:34
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is the step by step way to change the starter on a 95 S10?
Write your answer...
Related questions

How do you change a starter on a 1998 s10 The motor mount gets in the way?

To change the starter on a 1998 s10, the motor mount will have to be removed. Support the motor on a jack with a board on the top of it, and remove the mount to get to the starter.

What is the best way to change a starter on a 2001 silerado?

Whats the best way to change a starter on a 2001 silverado

How do you change the starter on a 84 s10 4x4 the easy way?

you remove the right side motor mount off of the motor and take the starter out through the top side behind the smog pump you my have to jack the motor up slightly

How can you replace a starter on a 1992 S10 4.3liter v6 motor - frame is in the way?

you have to remove the crossmember to do this.

How do you install a starter on 1998 Chevy S-10?

i just did a transmission change on a 90 s10 u probably have to drop gravel guard on transmission and starter should have two long bolts remove those and wiggle the starter out then carefully unbolt the two wires on the coil of the starter and be careful s10's usually have the two transmission lines in the way and those are a pain to replace hopes this helps and careful starter is heavy and u will prolly have to jack the vehicle up

How to change starter on Kawasaki Bayou 400?

the right way to change a starter on that bike is to take it to the dealer and tell him to change it.

How do you change the starter in a 1988 Isuzu Trooper?

to change the starter for Isuzu trooper is easy way to oper the exhaust pipe first.then you can reach easly to starter.

What is the easiest way to change the solenoid on a 1992 Corsica?

What solonoid?? If it is the starter solnoid, you have to take the starter off.

How do I change the starter on my 1986 Chevy Blazer?

the only way i could figure out how to get the starter out was to remove the right engine mount

How do you change a starter part on a 2000 Chevy venture?

What is the easiest way to replace the starter motor on a 2000 chev Venture?

How change s10 cigarette lighter?

Take the old one out and wire the new one the sam way.

How do you change your background on the inspiron mini 10?

If you have the same laptop I have, it came with Windows 7 STARTER (this is important!) If you have Starter, you can't change the background. Ever. This seriously annoys me, but there is no way to change it. If you have xp or Windows 7 (NOT STARTER) usually there is the Control Panel, and then Appearance and Themes. Then select Desktop and change the picture. (If this is what you have!)

How do you change windows 7 starter wallpaper?

For now, the only way is to download 3rd party software in order to change the backround. Type in starter wallpaper changer mediafire on google and download.

How do you change a starter for a V6 3.1 RS Camero engine?

How do you remove a starter from a 1995 Camero, I know it's from the bottom but the exhaust system is in the way.

What is the easiest way to change a starter on a 4 cylinder 1989 Cabriolet you can't seem to get at the top bolt on the starter from top or bottom?

The easiest way to get to the top starter bolt is with 12" extension and a 13 mil socket. You have to feel your way between the solenoid and the block. You can only take the starter off from the top if the engine is on a engine stand

Where can you find step by step instructions and a diagram of how to replace the starter on a 1999 Dodge Intrepid 2.7 liter V6?

The best way that I have found to remove the starter is to purchase or go to your local library and check out a copy of the Haines manual. I have used it to remove alternator, ECM, and the instrument cluster.

How do you replace starter on Chevy Venture 1998?

On a 98 venture the starter is located in front and just under radiator. Simple to reach and change. I learned the hard way.

How do you change the starter on a 1998 Ford Expedition?

Laying on your back under the vehicle! There are 3 bolts, 2 that are easy and the third which is on top of the starter, which you cannot see. Suggest you buy a NEW starter,as it is such a pain to change, you dont want to do it again anytime soon. Good luck Is there any way to change the starter without a floor jack/jack? The rinning boards are too low.

How do you replace abs brakes on 2002 Chevy s10?

You replace the brakes on an ABS S10 the same way you replace brakes on a non ABS S10.

How do you change a starter on a 1975 dart sport 360?

remove the wires from the starter and then the 2 bolts that hold it to the engine and it will come out as long as there is room without the exhaust manifolds or headers being in the way, if their in the way they have to be removed also.

What is the best way to remove 2 broken starter bolts broke off at the threads 95 Chevy s10 blazer?

Weld a larger nut to what is left of the broken bolt, let it cool then turn it out.

How do you Replace a Starter Motor in a Mitsubishi Eclipse?

In time, starters begin to wear out. The starter has a lot of moving parts and when just one of those parts wear out, the engine on your Mitsubishi Eclipse will not start. The most common part to wear out is the solenoid and the starter gear. Solenoids are replaceable, but you have to pull the starter out of the car to replace it. The gear is also replaceable, but it requires a starter rebuild. Most people opt for a new starter to obtain a warranty for the starter. 1. Step 1 Remove the negative battery cable from the battery with an adjustable wrench. 2. Step 2 Place the front end of the Eclipse on two jack stands so you can get under the vehicle. The easiest way to access the starter is raising the front of the vehicle and crawling under it to change the starter. However, you can remove the air cleaner ductwork and reach the starter without getting under the car. To do so, remove the band clamps that hold the ductwork to the throttle body and to the air filter box. With the ductwork removed, look down between the engine and the radiator to find the starter. 3. Step 3 Remove the solenoid electrical harness from the starter. Push the locking tab inward and pull the plastic harness off the starter solenoid. 4. Step 4 Remove the nut that holds the ground wire to the back of the starter with an adjustable wrench. Pull the wire off the stud and thread the nut back onto the stud to prevent losing the nut. 5. Step 5 Locate the two starter mounting bolts on the back of the bell housing. Remove the bolts with a ratchet and socket. Hold the starter in place with one hand while you remove the bolts with the other to prevent the starter gear from jamming into the flywheel. Jamming could damage the flywheel teeth. 6. Step 6 Pull the starter out of the bell housing. Pull any shims off the base of the starter and transfer them to the new starter. 7. Step 7 Push the starter into place. Turn the starter to mesh the starter gear with the flywheel in the bell housing. Turn the starter until the bolt holes in the starter and bell housing line up. 8. Step 8 Hold the starter in place and thread the two bolts from the back of the bell housing to secure the starter into place. Tighten the bolts to 30 ft-lbs. 9. Step 9 Remove the nut from the end of the starter and slide the black wire onto the stud. Replace the bolt and tighten it to 30 ft-lbs. 10. Step 10 Reconnect the wiring harness to the starter solenoid. 11. Step 11 Place the air cleaner ductwork onto the throttle body and secure the band clamp. Place the other end of the ductwork onto the air cleaner box and secure it with the band clamp. If you did not remove the ductwork, skip this step. 12. Step 12 Reconnect the negative battery cable to the battery.

How hard is it to change a starter on a 1992 crown Victoria?

The hardest part is the 3rd bolt on the 4.6 L engine. It is way up and in there. I would suggest that the best way is to buy the starter and have someone at a local garage with a car hoist change it for you. Check your local garage first before you buy the starter, some do not like to do this, but the one that does will only charge you about 1 hour labor.

How do you change your eye color step by step?

The only way to change your eye color is by buying colored contact lens. Don't listen to anyone who says otherwise as you might damage your eyes.

2002 Chevy s10 turn key won't start change the ignition switch and tumbler still won't start sometimes won't say anything then other times starts right up?

If both ends of the positive and negative battery cables are clean and tight, the starter may be telling you it is on its way out.