0
That can be calculated for individual cylinders by the formula :-
Pi R (2) x length of piston stroke.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the compression ratio for an engine if each cylinder has a maximum volume of 500 cubic centimeters and a minimum volume of 50 cubic centimeters?
Compression ratio is exclusive to each cylinder, though they will all have the same result if they are the same dimensionally ( and they always are) > Divide the total engine capacity by the number of cylinders, this gives the capacity or swept volume of each cylinder (bore * stroke) > So in a 2.0 (2000 cc) litre 4 cylinder engine, each cylinder has a 2000 / 4 = 500 cc swept volume (bore * stroke) > The combustion chamber is the volume remaining at top dead centre (TDC) > Compression ratio = volume at BDC (swept volume + volume at TDC) / volume at TDC
What is the total area of a cylinder with a height of 5 and radius of 2?
The volume of this cylinder would be 62.857142857142804 cubic units. The surface area of this cylinder would be 87.96459430051421 square units.
How do you get the volume of a cone when the volume of the cylinder is given?
multiply the volume of the cylinder by 1/3. whatever you get is the volume of the cone
How do you find the volume of a cylinder that is smaller on one end?
To find the answer to this question you would have to know how to find the volume of a cone. First, find the angle of the side to the base to determine at what height a cone would be formed if the sides of the cylinder extended all the way up to a single point. This would be the height of the cone. Take this number and put into the equation Assuming you know the radius of the cylinder at the bottom, the wider side. Next, subtract the total height of the cone from the height of the cylinder you want to know the volume of. You will now be finding the volume of the smaller cone within the larger cone. Put the smaller height into the above equation now using the radius of the top part of cylinder. Subtract this total from the total volume of the biggest cone and you will have the volume of a cylinder that is smaller on one end.
What is the volume of the cylinder?
Volume of a cylinder = base area times height
What are cubic inches in an engine?
Cubic inches is the total volume of all cylinders. If you wanted to know the cubic inches of a particular engine you would measure the diameter of the cylinder bore and the stroke of the crankshaft, then use your calculator to figure out the total volume. The formula for the area of a circle is pi times the radius squared. The formula for the volume of a cylinder is area of the circle times length (stroke) of the cylinder. Once you have the volume of the cylinder you can multiply that number by the number of cylinders for total volume (displacement).
Calculate the cubic capacity of a 6 cilynder engine with a bore of 85mm and astroke of 90mm?
no of cylinders = 6 bore = 85 mm =8.5cmstroke = 90mm =9 cmbore area = bore * bore * pi/ 4 (pi=3.14159)volume of 1 cylinder = bore area * strokeengine capacity = volume of 1 cylinder * no of cylindersbore area = 8.5 * 8.5 * 3.14159/ 4=56.745 square cmvolume of 1 cylinder= bore area * storke=56.745*9=510.7 cubic cm (cc)engine capacity =volume of 1 cylinder * no of cylinders=510.7 * 6=3064.22 cc
What is the compression ratio for an engine if each cylinder has a maximum volume of 500 cubic centimeters and a minimum volume of 50 cubic centimeters?
Compression ratio is exclusive to each cylinder, though they will all have the same result if they are the same dimensionally ( and they always are) > Divide the total engine capacity by the number of cylinders, this gives the capacity or swept volume of each cylinder (bore * stroke) > So in a 2.0 (2000 cc) litre 4 cylinder engine, each cylinder has a 2000 / 4 = 500 cc swept volume (bore * stroke) > The combustion chamber is the volume remaining at top dead centre (TDC) > Compression ratio = volume at BDC (swept volume + volume at TDC) / volume at TDC
What is a cylinder bore barrel?
A Cylinder bore has no choke at all.
1992 trx 250x a valve broke off damage to the head and piston did not hurt the cylinder can you just get it honed or does it need bored out?
If there was no damage to the cylinder bore then you will not need to bore it oversize.If there was no damage to the cylinder bore then you will not need to bore it oversize.
How do they differ higher and lower displacement engines?
taking one cylinder , area of bore * length of stroke gives displacement (or volume) of one cylinder , then * number of cylinders = total engine displacement for rough power calculation you can research the equation PLAN/33000
What is an aircraft piston engine cylinder bore?
The bore refers to the Inside diameter of the cylinder. The Piston will be nearly the same diameter, with the piston rings making up the difference. Convert the bore to area by multiplying by pi and dividing by four, and multiply by the stroke and the number of cylinders and you have the volume displacement of the engine.
How do you get cubic inches in a motor?
you take the volume of each cylinder and add them together. the volume is calculated using the bore (width of cylinder) and the stroke (the height of where the piston reached the top [crank angle of 0 degrees] to the bottom [crank angle of 180 degrees]) volume = pi (3.14159) x radius (1/2 bore) squared x height (stroke of the cylinder) that will give you cubic inches per cylinder. Then just multiply by the number of cylinders in the engine.
Is cc similar to swept volume or total cylinder volume?
CC is Cubic Centimeters, an unit of volume by itself. It can be either swept or total volume depending on circumstances.
Is the bore of a cylinder the circumference?
The bore of a cylinder describes is measurement, in millimeters or inches, of the inside diameter of the cylinder. The diameter is the width across.
What is the derivation of the formula for volume and total surface area of a cylinder?
Volume = Пr2h Area = 2Пr2+2Пrh (where r=radius of base, h=height of cylinder)
Does micrometer measure inside of a cylinder?
Yes. An inside micrometer or bore micrometer can be used for measuring the bore of a machined cylinder.
