0
What kind of wire do you use for 120 volts and what amp breaker do you use?
Wiki User
∙ 15y ago
#12/2wground & a 20 amp breaker should be enough for lights,receptales.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What can you operate on 120 volts at 30 amps?
Yes, if you are using AWG # 10 wire. If you are using AWG # 12 then the answer is no you must use a 20 amp breaker. On AWG #14 wire you must use a 15 amp breaker.
How will a 3 phase panel give you 110 volts and 220 volts?
A three phase panel will not give you 110 and 220 volts. A three phase four wire panel will, but not at these voltages. The nearest voltages will be 120 and 208 volts. The 120 volt is the wye voltage of 208 volts. 208/1.73 = 120 volts. A single phase three wire panel will give you 110 and 220 volts.
How do you connect wire to a breaker?
There is 220 volts between the two poles. If you are running 2 wires (black and white) + ground then you hook black to one pole and white to the other. Put red or black electric tape on each end of the white wire and wrap around wire for 3 inches or so next to the connection so the next person will be able to see that the wire is hot and not a neutral.
Gauge wire needed for 8 amp sump pump?
you will need wiring that is at least 10 amp rated wire or higher. If you really needed to ask you might want to call an electrician Electrician here, be the pump 120 volts or 240 volts a #14 wire will handle the situation. Longer runs of 75 feet you should go to a #12 wire to compensate for voltage drop. The pump should be on its own separate circuit with a 15 amp breaker. A two pole 15 amp breaker if the pump is 240 volts.
Do you need a 20 amp single or double pole breaker for your washer?
Washing machines in the U.S. operate on 120 volts. That requires a single pole 20 amp breaker and wired with 12/2 w-ground wire. Black to the breaker, white to the neutral bus bar, and copper ground to the ground bus bar.
How do you wire a wire to a wire?
If you are connecting 120 volts, you connect the black wire to the breaker, white wire to the neutral bar, and ground wire to the ground bar. If you are connecting 240 volts connect the black & white wires to the breaker, & ground wire to the ground bar.
What can you operate on 120 volts at 30 amps?
Yes, if you are using AWG # 10 wire. If you are using AWG # 12 then the answer is no you must use a 20 amp breaker. On AWG #14 wire you must use a 15 amp breaker.
How can I get 230 volt single pole wire from my house panel?
In North America you can not obtain 230 volts from just one single pole breaker. The distribution is like this, from a one pole breaker to neutral is 120 volts. From an adjacent breaker to neutral is 120 volts. From the adjacent breaker to adjacent breaker (breakers situated beside each other) the voltage will be 230 volts.If you want to incorporate a 120 to 230 volt transformer into the circuit you can obtain 230 volts. The primary side of the transformer will be connected to the 120 volt circuit and the secondary side of the transformer will output 230 volts. The transformer must be sized to the load amperage or the load wattage of the connected 230 volt load.
Can you use 240 volts with a 120 volt supply?
Only if the cable going to your well pump is a three wire. The third wire could carry the neutral and you will have 120 volts from either 240 leg to the neutral.
What should the reading at the light switch be when the switch and the light fixture is removed. I had a dimmer switch on that light it went out I checked the volts at the switch they were about 14?
On the "hot"wire that comes from the breaker panel the voltage should be from 115 to 120 volts. This is taken from the "hot" wire to either the neutral or the ground wire. If its not then you have a breaker problem or you are on the wrong scale of the test meter.
Why am I only getting 120 volts from a 30 amp breaker that should be feeding 220 volts?
I assume you have a 30 amp two pole 220 volts breaker. Check the voltage source. If the source voltage is 220V, but out let voltage is 120 then the breaker must be faulty, a high resistance or partial open circuit could have caused the reduced voltage at the breaker outlet.
Can a 15 amp breaker hold 300 watts at 120 volts?
Yes, it can.
Can a 3 wire load center be use in a 2-wire environment?
yes you can. but you will have less 220 v circuits. <<>> In North America if you only have a two wire supply it is usually 120 volts. To connect a three wire load center to this supply, a jumper wire is connected across the two lugs that would have taken the 240 volt input if you had that supply voltage. This is where your 120 volt supply is connected. The neutral of the 120 volt supply connects to the neutral buss bar. What this connection does is "hot" up both sides of the buss bar so that you will have 120 volts on each breaker outlet. By eliminating the jumper you would only have every other breaker slot energized.
What is ampere rating of 10 gauge wire at 120 volts and at 240 volts?
30 amps.
How will a 3 phase panel give you 110 volts and 220 volts?
A three phase panel will not give you 110 and 220 volts. A three phase four wire panel will, but not at these voltages. The nearest voltages will be 120 and 208 volts. The 120 volt is the wye voltage of 208 volts. 208/1.73 = 120 volts. A single phase three wire panel will give you 110 and 220 volts.
How do you connect wire to a breaker?
There is 220 volts between the two poles. If you are running 2 wires (black and white) + ground then you hook black to one pole and white to the other. Put red or black electric tape on each end of the white wire and wrap around wire for 3 inches or so next to the connection so the next person will be able to see that the wire is hot and not a neutral.
Can a 125 volt cable power a 120 volt piece of equipment?
The first thing we have to do is clarify the question. A cable rating of 125 volts is an insulation rating of the wire. Like wire with ratings of 300 volts, 600 volts and 1000 volts these are the highest allowable voltages that can be applied. A wire that is rated for 300 volts is good for 120 volts, 240 volts and 277 volts. At test research facilities, equipment is tested to destruction. The label that is given to wire as a result of the tests is the highest safest voltages that can be applied to that particular wire. So when you see a wire that has a label stating that it is rated for 300 volts it means that any voltage under and up to 300 volts is safe to apply. So to answer the question yes, the 125 volt insulation rating on the cable can be used to supply a source of 120 volts to a 120 volt rated piece of equipment.
