0
What percentage is the maximum allowable conductor fill of any trade size conduit used as a raceway?
Wiki User
∙ 11y ago
It depends on the wiring, the current load in the wiring , and the distance. The NEC Code book has the charts for this.
And the size of the conduit.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the maximum allowable conductor fill of any trade size conduit used as a raceway?
It depends on the wiring, the current load in the wiring , and the distance. The NEC Code book has the charts for this.And the size of the conduit.
What is considered to be the maximum allowable supply voltage variation?
+or- 5%
How many percentage leakage current allow?
The maximum allowable leakage current for any electrical device is 0.5 mA. This is equivalent to 0.5% of the rated current. This is a safety requirement to ensure that any current leakage is minimal and will not cause any harm to the user or damage to the device.Maximum allowable leakage current: 0.5 mAEquivalent to 0.5% of the rated currentIt is important to adhere to the safety requirements to ensure the safety of users and the protection of the device.
What size electrical wire underground 230 volt 60 amp 800 feet?
NEC recommends maximum allowable voltage drops not to exceed 3% on a branch circuit. For feeder/ branch combos the NEC recommends that the voltage shall not drop by more than 5% to the furthest outlet. The main consideration that is enforced is NEC 250-122. You must compensate your grounding conductor when you increase in conductor size to compensate for voltage drops. Direct bury or conduit: #4/0 copper provides for 2.95% #2/0 copper provides for 4.35% #1/0 copper provides for 5.19% Interestingly enough, using a separate calculator 3/0 copper with 3% voltage drop can be 780.5 feet long.
What is the resistance of acsr moose conductor?
0.0547 ohms/km - maximum DC resistance at 20'C. Britsh Standards.
What is the maximum allowable conductor fill of any trade size conduit used as a raceway?
It depends on the wiring, the current load in the wiring , and the distance. The NEC Code book has the charts for this.And the size of the conduit.
What size conduit for 400amps?
The sizing of conduit systems that wire has to be pulled into is dependant on the physical size of the conductor being drawn into the conduit. The second governing factor is the conductor count of the specific conductor that is needed. A 500 MCM copper conductor with an insulation factor of 90 degrees C is rated at 430 amps. This is where the conductor count is need by the service, as to whether the service is single or three phase. In this specific case, the electrical code will allow both single and three phase installations to use the same size conduit. A maximum total of four 500 MCM conductors can be drawn into a 78 mm diameter conduit.
What is the maximum percentage allowable on a wage garnishment with child support garnishment in the State of Oklahoma?
The maximum percentage allowable is 65 percent. This can only be taken out if the garnishee does not support a second family and owes more than 12 weeks of back child support. If the garnishee does support a second family, the maximum is 55 percent if he owes more than 12 weeks of back child support, and 50 percent if he does not.
What is MAWP?
Maximum Allowable Working Pressure
What is the maximum allowable hop for RIP?
15
What is the act of tolerance?
The maximum allowable size that can be altered.
Identify this acronym:MAAC?
Maximum Actual Allowable Charge
The level of significance is the maximum allowable of what?
Type I error.
What is the maximum degrees bending for conduit?
its 180 degrees If you use the above answer the conduit will flatten and close off. The maximum degrees for a single bend in conduit is 90 degrees. Also code only allows four 90 degree bends in a conduit run between pull boxes.
Is epsilon the same as maximum allowable error?
Yes, in statistics, the epsilon symbol is used for maximum allowable error. http://www.liaad.up.pt/~jgama/IWKDDS/Papers/p14.pdf
What is considered to be the maximum allowable supply voltage variation?
+or- 5%
Full form or mail?
Maximum Allowable Industrial Loading
