0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What size hole needs to be drilled for a number 6 screw?
#4 Screw use a 1/16" Drill #6 Screw use a 3/32" Drill #8 Screw use a 1/8" Drill #10 Screw use a 9/64" Drill #12 Screw use a 11/64" Drill #14 Screw use a 3/16" Drill
How do you use other sources of information to support the data?
In engineering you can use items around the workshop such as posters on info boards or their may already be drill and hole sizes for tap for example a 6.8mm drill bit for a M8 tap on a technical drawing or bend tolerences for the materials thickness.
How do you drill into brick to attach address numbers?
Use a carbide bit in a drill. Then install plastic anchors where the screws go.
How do fashion designers use fractions in there job?
they use it to get the right size of fabric to use
Can you show me a life size protractor?
Actually, any protractor you can find online is life size, but here's a website you can use. Check the link for a website you can use.
What drill bit size for .125 in. national pipe thread?
Use 7/64 as tap drill and 9/64 as clearance drill
What size drill bit should you use to drill a hole that is threaded for a 1by4-20 UNC bolt?
Your meaning is not clear. - If you are going to tap the threads in, use a 7/32 drill bit. If you want a hole that this bolt will slip through, use a 9/32 drill bit.
How can you get a stripped screw off?
drill off the head remove whatever it held down use vicegrips to remove the rest becarful not to drill to deep or brake the saft off or youll have to drill and tap out the hole for another size screw
What size drill bit for a seven sixteenth inch tap?
I use a 3/8 bit for tapping fine thread, or a 11/32 for coarse threads.
What drill do I need for a 5 mm tap?
4.3 is best or a 4.2 but use pleny of oil
What do you do when you break a bolt that attaches the thermostat housing to the engine?
You drill the bolt out that is snapped off in the engine,with drill bit made to drill through metal. Then use a thread maker,tap. Auto parts stores carry these. I no u can get at autozone. The tap makes new threads.
How do you drill 0.5mm hole?
If no drill bit this size available, can use EDM service if metal is used
Could the reversable drill bit extract a broken bolt?
Not unless it was reasonably loose. Usually when faced with this, I drill into the bolt with a very hard drill bit a tiny bit thinner than the bolt - ie if it's a 3/8 bolt, I drill in first with a 1/8 drill to create a guide hole, then after with a 5/16 drill to cut right through, yet not harm the threads. You have to be very careful to stick to an exactly straight course. After the hole is cleared, I pull the threads left from the bolt out as far as I can, then use a 'clearance' tap of bolt size to re-tap the hole.
How do you use other sources of information to support data?
In engineering you can use items around the workshop such as posters on info boards or their may already be drill and hole sizes for tap for example a 6.8mm drill bit for a M8 tap on a technical drawing or bend tolerences for the materials thickness.
What size drill bit should you use for a hole to be tapped for a .25 x 20 screw?
I use a 3/16 drill bit for that.
What size drillbit do you use in inches for a 16mm drill bit?
I would use a 5/8 drill bit which is almost exactly 16mm.
What size hole needs to be drilled for a number 6 screw?
#4 Screw use a 1/16" Drill #6 Screw use a 3/32" Drill #8 Screw use a 1/8" Drill #10 Screw use a 9/64" Drill #12 Screw use a 11/64" Drill #14 Screw use a 3/16" Drill
