Number 10 thnn copper wire.
I'm assuming you mean 100 amp service, not circuit breaker? The NEC code states the minimum service is 100A. Depending on your definition of "small", this would be sufficient. It all depends on your large loads too (Electric water heater, Air conditioner, electric range, etc). These appliances can pull some large amperage.
That will draw about 9 amps at 120V. A 15 amp breaker if the circuit conductor is #14 or 20 amp breaker if the circuit conductor is #12. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed. Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
A 15 amp circuit breaker is used to protect a # 14 copper wire which is the minimum size wire that can be connected to a 15 amp receptacle.
JAMES SIX invented the Maximum and Minimum thermometer in 1782.
The minimum and maximum refers to the number of sunspots.
Read the literature for the ac condensing unit, or the tag on the outside of the unit. Minimum circuit ampacity= minimum breaker, wire and fuse size. Maximum circuit ampacity= the maximum size. Your circuit breaker, wire size and disconnect fuses should all be at or between those 2 numbers.
Inside the circuit loop between the inductor and capacitor the current will be at maximum. Outside the circuit the current through the LC tank circuit will be at minimum. It depends on where you are measuring it.
For a particular frequency if the current or the voltage of the circuit is Maximum or Minimum then that circuit is said to be in resonance .
30 m amp
If you have the Maximum clock frequency, then you can figure out the minimum clock period using this formula: 1/(minimum clock period) = (Maximum clock frequency).
High voltage switch gear operates in the voltage range of 36 kV and above. Minimum oil circuit breaker, air blast circuit breaker and SF6 (Sulphur hexafluoride) circuit breaker are the three mostly used disconnects for high voltage switchgear.
A circuit breaker limits the amps that a circuit can carry. If the amperage draw on a circuit exceeds that limit, the circuit breaker turns off the circuit. If the current through a wire exceeds the rated amperage, the wire will overheat and eventually cause a fire, or at a minimum, destroy the wire behind inside the wall. Obviously, people don't want a house fire caused by an electrical overload, so circuit breakers are used to prevent damage and potential loss of life.
Most often if you add up all the breaker values in a panel they will exceed the rating of the panel. The theory is that you never operate each breaker to its full capacity. The panels are sized to the maximum current that is capable of being supplied by the electric company equipment servicing your house. Correction: Panels are sized according to the outcome of a complicated process of estimating the maximum number of amps that are likely to be used at any one time. This gives you a minimum size and you install AT A MINIMUM the next larger size panel. I don't know of a maximum size by code but there are limits to what can be practically used. In the absence of this complicated process, there are some rules of thumb that are substituted on houses. These range from 100 amps to 200 amps.
I'm assuming you mean 100 amp service, not circuit breaker? The NEC code states the minimum service is 100A. Depending on your definition of "small", this would be sufficient. It all depends on your large loads too (Electric water heater, Air conditioner, electric range, etc). These appliances can pull some large amperage.
150W = 240 volts * .625Amps. Assuming the 20A breaker trips at exactly 20A, 20/.625 = 32 lights.
The extrema are the maximum and minimum values.The extrema are the maximum and minimum values.The extrema are the maximum and minimum values.The extrema are the maximum and minimum values.
The opposite of minimum is maximum.