0
What type of scope mount would go on a Sears Ranger 101.13 with two holes that look like they were factory drilled and tapped on the left side of the receiver?
Wiki User
∙ 17y ago
The Ranger 101.13 (.22 caliber, clip fed, bolt action) was fitted with a side mount that was stamped with "T3" and anchored with slotted thumb screws marked "F" and "R" (front and rear). The scope that came with the rifle was a "Wee Weaver" M. 3-29, 4-power, Weaver scope. If you would like I could email you pics of the mount. Just email me at: BLKLION@MC.NET --- bill
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
What kind of base mounts are needed for a JC Higgins 22 cal rifle Model 10313 that has two pairs of tapped screw holes on the side of the bolt housing and chamber?
That gun was made by Marlin for Sears, and those holes are not factory. Someone has drilled and tapped it for (probably) a Weaver side-mount base.
How many syllables does tapped have?
2 syllables......... Addition: Just count how many vowels the word has. So in this case the word "trapped" has two vowels....
What are the real life applications of bridge rectifier?
It's the only way to accomplish full-wave rectification of AC without a center-tapped transformer winding.
How many threads are in a 3 8ths 24 UNF tapped hole that is 32 thousandths deep?
A 3/8ths 24 bolt has 24 threads per inch (TPI), and a 32 thousandths (0.032) hole that has been completely bottom tapped for 3/8ths 24 fastener will have 24 x .032 or 0.768 threads in it. And yes, that isn't even one complete turn of the bolt before it bottoms out.
What is a number alliteration?
A number alliteration is when each line starts with its number and all the words in the line start with same sound (ex line 2: Two Toms tapped there tippity tappity toes)
Was the Winchester model 75 sporter ever drilled and tapped from the factory?
yes for a target scope .
How many factory tapped holes are in the receiver of a 19 NRA match rifle?
None
How can you mount a scope on a Stevens Savage 12 gauge pump model 520?
The receiver will need to be drilled and tapped for a mount. See a gunsmith.
How do you put a scope on a savage 24e-dl it is not drilled and tapped for a mount?
You will have to have a trained and competant gunsmith drill and tap your receiver for a set of rings and bases to mount a scope on your savage.
Is a Remington model 4407 drilled and tapped?
nope
What is tapped hole?
That is hole that has been drilled, then had a thread 'tapped' into it so you can insert a machine screw or bolt.
What scope and mounts can be purchased for a 22 caliber Glenfield Model 75 bolt action that has not been drilled or tapped?
These guns were never drilled/tapped for scope mounts. Like most inexpensive .22 rifles, the top of the receiver is grooved for tip-off mounts. The mounts and rings are typically one piece, and sold virtually everywhere - even WalMart.
Does an Inter Arms 30-06 mark x have predrilled holes in the barrel for a scope?
There are several different models of the Mark X, however, most have a RECEIVER that is drilled and tapped for a scope- not the barrel.
What is the proper scope base for a Ranger 22LR with heavy target barrel?
I seem to recall that may be the same gun as a Stevens 416. Most of those guns did not have drilled and tapped recievers. They did have drilled and tapped barrels for old style target scopes. You will probably do better to take it to a competent gunsmith and have him drill and tap it to fit a currently available scope base.
What scope mount to use on a Remington score master 511p 22 cal rifle?
The Remington Score Master .22 rifle does not come from the factory drilled and tapped for a scope base. If you choose to have that work done, you can buy a set of bases that fit this particular rifles receiver. The most economical bases are those sold by Weaver. The number for the base fitting on the rear of the receiver would be the Weaver top mount, #43. The mount that will fit on the front of the receiver would be the Weaver top mount #42. These bases would require that the top of your rifles receiver be drilled and tapped to accomodate these bases. All of the 500-series Remington rifles (.22 rimfire caliber) have the same type of receiver and use these bases. With these bases you can use one-inch tube diameter scopes and rings to get a better field-of-view and clarity over the low cost 3/4-diameter scopes. Any competent gunsmith will be able to do this work for you.
Is Marlin 883 drilled and tapped for scope bases?
no it has a 3/8 dovetail rail
How do we collect natural gas?
Shafts are drilled deep into the ground and the gas is tapped and brought to the surface.
