0
What else can I help you with?
What is a circle shape cut from a cone?
It is a section formed by a plane at right angles to the axis of the cone.
What is half of a cone?
it a cone cut in half from the top
What is a cross section of a right circular cone?
A cross section of a right circular cone is a two-dimensional shape obtained by slicing the cone perpendicular to its axis. Depending on the position of the cut, the cross section can be a circle, an ellipse, or a triangle. If the cut is made parallel to the base, the cross section will be a smaller circle. If the cut is made vertically through the apex and perpendicular to the base, it will form a triangle.
What is the cross-sectional area of a 3D shape all about - explained simply as possible please?
You have a 3-d shape. If you slice of a part of it with a very very sharp instrument (a sharp sword or a laser, for example) the cross section is the shape of the newly cut surface. So, if you start with a sphere, any section will be a circle. Of different sizes depending on how high or low you cut, but they'll all be circles. If you have a cone, a dead vertical cut, through its apex (top point) will be a triangle. But as you move off the apex, you will get a parabola. Cut is horizontally, though, and you will get circles - ncreasing in size as you move further from the apex. Cut it at a slight slant and you will get ellipses (ovals). And so on.
What shape has one curved face and two flat faces?
A cylinder, a doughnut with a slice cut out by radial planes, a sphere with two slices removed (possibly in a wedge shape), a cone with its top and bottom cut off by horizontal planes, a paraboloid with top and bottom cut off by horizontal planes.
What would a cone look like if it was cut horizontally?
It depends how the cone was standing relative to the horizontal plane of the cut:It will result in:a circle (if the cone is with its circular base in a horizontal plane)a parabola (if the cone is with its circular base is in a vertical plane)an ellipse (if the cone is tilted with its circular base somewhere between a horizontal plane and a vertical plane).
What is a circle shape cut from a cone?
It is a section formed by a plane at right angles to the axis of the cone.
How can you make a cone out of paper?
To make a cone out of paper, start by cutting a sector from a circle. Then, overlap the cut edges to form a cone shape and secure them with glue or tape. Finally, trim the base of the cone to make it even.
When a sphere is cut into cross sections what is the shaped formed?
When a sphere is cut into cross sections, the shape formed is a circle. This is because all cross sections of a sphere will be circular in shape, regardless of the angle or position of the cut.
What do you call a cone with the top cut off?
This shape is known as a Conical Frustum. Please see the related link.
What is produced when you slice a cone at different angles?
When a cone is sliced parallel to the base then the shape produced is a circle. If the cone is sliced at an angle so that the cut goes completely through the cone then an ellipse is produced. If the cut is made perpendicular to the cone's base then the shape produced is a parabola.
What is half of a cone?
it a cone cut in half from the top
What is a cross section of a right circular cone?
A cross section of a right circular cone is a two-dimensional shape obtained by slicing the cone perpendicular to its axis. Depending on the position of the cut, the cross section can be a circle, an ellipse, or a triangle. If the cut is made parallel to the base, the cross section will be a smaller circle. If the cut is made vertically through the apex and perpendicular to the base, it will form a triangle.
What is a truncated cone?
A truncated cone is basically a cone with it's tip cut off.
What is frustum of cone?
There is no frustum of a cone. There is a frustum, which is a cone with the top cut off parallel to the ground.
What is the cross-sectional area of a 3D shape all about - explained simply as possible please?
You have a 3-d shape. If you slice of a part of it with a very very sharp instrument (a sharp sword or a laser, for example) the cross section is the shape of the newly cut surface. So, if you start with a sphere, any section will be a circle. Of different sizes depending on how high or low you cut, but they'll all be circles. If you have a cone, a dead vertical cut, through its apex (top point) will be a triangle. But as you move off the apex, you will get a parabola. Cut is horizontally, though, and you will get circles - ncreasing in size as you move further from the apex. Cut it at a slight slant and you will get ellipses (ovals). And so on.
What shape has one curved face and two flat faces?
A cylinder, a doughnut with a slice cut out by radial planes, a sphere with two slices removed (possibly in a wedge shape), a cone with its top and bottom cut off by horizontal planes, a paraboloid with top and bottom cut off by horizontal planes.
